Stanley SG6115, Инструкция по эксплуатации

Страница: 28 / 36

28
ENGLISH (Original Instructions)
Hz Hertz Class II
Construction
W Watts Earthing
Terminal
min minutes Safety Alert
Symbol
Alternating
Current
/min. Revolutions or
Reciprocation
per minute
Position of date code
The Date Code, which also includes the year of manufacture,
is printed into the housing.
Example:
2020 XX JN
Year of manufacturing
PACKAGE CONTAINS
The package contains:
1 Angle Grinder
1 Guard
1 Flange set
1 Spanner
1 Handle
1 Instruction manual
• Check for damage to the tool, parts or accessories
which may have occurred during transport.
• Take the time to thoroughly read and understand this
manual prior to operation.
FEATURES (Fig A)
WARNING: Never modify the power tool or any part of the
tool, otherwise it may cause damage to the tool or result in
personal injury.
1. ON/OFF Switch
2. Spindle Lock
3. Guard
11. Side Handle
ASSEMBLY
WARNING: To prevent accidental operation,
turn off and unplug tool before performing the
following operations. Failure to do this could
result in serious personal injury.
Attaching and removing the wheel guard (Fig B)
WARNING: To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/installing any accessory. Before
reassembling the tool, press and release the
trigger switch to make sure the tool is already
switched off.
Attaching the guard (Including Type27/41/42 Guard)
1. Place the angle grinder on a work bench, with the spindle
facing the operator .
2. Pick up the guard and make sure that the bump(10) of
the guard is aligned with the groove(9) of the gear case
cover.
3. Release the guard(3) and turn the guard counterclockwise
by 180 degrees.
4. Tighten screw(12) and make sure the guard does not
turn.
Removing the guard (Including Type27/41/42 Guard)
1. Loosen the screw(12) on the guard collar .
2. Turn the guard counterclockwise by 180 degrees.
3. Pull up the guard(3).
Attaching and removing grinding wheels(Fig C and D)
WARNING: Do not use damaged grinding
wheels.
1. Place the tool on a work bench, the spindle facing the
operator.
2. Attach the inner flange (4) correctly on the spindle (5).
3. Place the grinding wheel (6) on the inner flange
(4).When attaching a grinding wheel with a raised
center,make sure that the raised center (7) faces the
innerflange (4).
4. Tighten the outer flange (h) onto the output shaft (5).
5. When attaching the grinding wheel, the ring on top of
the outer flange (8) must face towards the wheel (Fig
D-1); When attaching the cutting wheel, the ring on top
of the outer flange (8) must face away the wheel (Fig
D-2).
6. Press the spindle lock (2) and prevent the spindle (5)
from rotating until it locks in place.
7. Use the pin spanner to tighten the outer flange (8).
Attaching the Side Handle (Fig A)
WARNING: Before using the tool, check that the
handle is tightened securely.
WARNING: The side handle should always be
used to maintain control of the tool at all times.
Screw the side handle (11) tightly into one of the
holes on either side of the gear case.
Preparation before use
• Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding wheels
that are overly worn.
• Make sure that the inner and outer flanges are attached
correctly.
• Make sure that the abrasive or grinding wheels are
rotating in the direction of the arrows on the accessories
and tool.
WARNING!
• Make sure all materials to be grinded are secured in
position.
• Apply slight pressure to the tool. Do not apply side
pressure to the abrasive disc.
• Avoid overloading. If the tool becomes hot, let it spin for
a few minutes with no load.