manualshive.com logo in svg

SRAM Rock Shox Lyrik 2019, Руководство по обслуживанию, Страница: 59 / 75

Поделиться
Скачать
SRAM Rock Shox Lyrik 2019 Скачать руководство пользователя страница 59

59

Test Compression

T e s t   C o m p r e s s i o n

Use the adjuster knob to rotate the compression cam clockwise, until it 
stops, to the firm position.
The cable tie must be 

34 mm

 from the end of the shaft. 

Do not 

compress the rebound damper further than this point.

Cover the purge hole with a shop towel.

⚠

CAUTION

Oil may exit the cartridge tube purge hole. Wear saftey glasses and 
keep your eyes and face away from the purge hole when compressing 
the rebound damper.

Push down on the damper assembly slowly to test the firmest 
compression setting. Firm and consistent resistance should be felt with 
no gaps in movement.
Rotate the compression damper to open setting and repeat the 
compression test. Light consistent resistence should be felt with no 
gaps in movement. 
If gaps are felt during compression, repeat the oil fill and purge 
process. If the assembly process was successful, set the compression 
damper to the open setting and remove the cable tie.

1 

Содержание Rock Shox Lyrik 2019












































































Отзывы:

Нет отзывов