Spudnik 290318, Руководство пользователя

Страница: 15 / 77

P
ARTS
M
ANUAL
4300 BULK BED
Part #: 290318
Revision: 4/18/2018
5
Section
-
1 Safety
1.15. Machine Storage
1. Thoroughly clean the machine before placing it in
storage.
2. Lubricate moving parts and protect bare metal before
placing the machine in storage.
3. Store the machine in a dry, level, protected area.
4. Store the machine away from human activity.
5. Do not permit children to play on or around the stored
machine.
1.13. Electrical System and Electronics
1. Remove conductive jewelry, e.g. metal rings,
bracelets, watches, etc., before working on or around
electrical circuits.
2. Use only original fuses with the specified current
rating. Switch off the machine immediately if a fault
occurs in the electrical power supply.
3. Always disconnect the wiring harness between the
machine and the tractor before servicing the electrical
system or welding on the machine.
4. Work on the electrical system or equipment may only
be carried out by a qualified electrician, or by specially
instructed personnel under the control and supervision
of a qualified electrician, and in accordance with the
applicable electrical standards/regulations.
5. The machine’s electrical equipment is to be inspected
and tested at intervals specified in this manual.
Defects such as loose connections or scorched cables
must be rectified immediately.
6. The machine is fitted with electronic components and
modules, the function of which may be influenced by
the electromagnetic fields of other equipment. Such
interference can lead to potentially dangerous
situations if the following safety advice is not observed.
7. If electrical or electronic devices and/or components
are retrofitted to the machine then it is the
responsibility of the user to check whether such
installations interfere with the vehicle's electronics or
other components.
This applies particularly to:

Mobile telephones

Radio equipment
8. The following conditions must be satisfied if mobile
communication systems (e.g. radio, telephone) are to be
installed after the original delivery of the machine.

Only approved devices complying with the relevant
national regulations may be installed.

The device(s) must be installed permanently.

The mobile device(s) in the tractor or on the machine
must be connected to a permanent external aerial.

A properly installed aerial must maintain a good ground
connection between the aerial and vehicle chassis.

The transmitter assembly must be isolated from the
vehicle electronics.
9. Use only the specified wiring/conductor gauge for
electrical systems on the machine.
10. Do not exceed the maximum specified current
consumption for any electrical system.
1. Always observe the relevant safety measures and in-
structions specified in the Owner/Operator manual
when carrying out the operation, maintenance, inspec-
tion, repair, adaptation, or conversion of the machine.
2. Keep all operational and maintenance areas clean and
dry. Clear dirt, snow, ice or any other debris that could
pose a hazard, from handles, steps, handrails, plat-
forms, landings and ladders.
1.16. Maintenance and Inspection Guidelines
To prevent accidents, all relevant rules and
regulations concerning safe and competent working
must be observed.
IMPORTANT
1.14. Hydraulic Systems
1. Lower the machine, depressurize the system, switch
off the engine and remove the key before working on
the hydraulic system.
2. Use caution when working on the hydraulic system.
Hot hydraulic oil can cause serious burns. Allow the
hydraulic system to cool before starting work, and
wear gloves. Collect and dispose of used oil in
accordance with local/national regulations.
3. Hydraulic hoses should be inspected at intervals
specified in this manual, and replaced if damaged or
worn. New hoses must comply with the technical
specification of the machine manufacturer. Hoses and
hose couplings undergo a natural aging process, even
if stored and used correctly; therefore, their period of
storage and use is limited. The service life of a hose
may deviate from manufacturer estimates. Considering
the potential danger from hydraulic hose failure,
replacement decisions should err on the side of
caution.
WARNING!
The hydraulic system operates under high pressure.
Depressurize the system before working on any
component in the system.