Spokey AURIS, Руководство пользователя

Страница: 18 / 54

18
www.spokey.eu
www.spokey.pl
ATTENTION: Before transporting the treadmill make sure that it is
disconnected from power supply. The device should always be transported
by two persons.
MAINTANCE
Caution: before cleaning / lubrication you must take out the power plug from
a socket.
For cleaning the exercise machine, do not ue any abrasive detergents. Use
a soft, damp cloth to remove dirt and dust.
The monitor should be cleaned only with a dry cloth.
The equipment should be stored in dry places in order to protect it from any
moisture and corrosion.
Use a soft, damp cloth to wipe off the edges of the treadmill belt, and the
space between the treadmill belt and the frame edges. Clean the edge of
the belt on its bottom side also. Clean the upper part of the belt with a brush
and soap water once a month. NOTE: Before you start using the treadmill again, wait until the equipment
is completely dry.
Vacuum under the equipment at least once a month to prevent dust from
accumulating.
Once a year, it is recommended to remove the black cover of the engine in
order to remove any dust that may accumulate there.
NOTE: The level of equipment operational safety can be maintained only
by regular inspections checking for any damage and wear.
Connecting elements are the most vulnerable to any wear..
BELT TENSION ADJUSTMENT
To:If deviate to the right, then adjust the screw on the right side
clockwise or the screw on the left side anticlockwise.
If deviate to the left, then adjust the screw on the left side
clockwise or the screw on the right side anticlockwise. Use the wrench to turn the adjusting bolt clockwise
until the driven belt is not slippery anymore.
Note: Regular clean any objects that fell between
The driven belt. This is a mandatory process.
BELT TRACKING ADJUSTMENT (PICTURE, P. 7)
This treadmill is designed to keep the belt reasonably centred while in use.
It is normal for some belts to drift near one side while the belt is running
with no one on it. After a few minutes of use, the belt should have a
tendency to centre itself. If during use, the belt continues to move toward
one side, adjustments are necessary. The procedures are as below:
▲ First set speed at lowest position.
▲ Second check the belt shifts to which side. If the belt shifts to right, tighten the right bolt and loosen the left bolt by
using 6mm Hexagonal Wrench, until the belt is centered itself; if belt shifts
to left, tighten the left bolt and loosen the right bolt by using 6mm Hexagonal
Wrench, until the belt is centered. When adjusting the belt using the 6 mm
Hexagonal Wrenches, it is important to adjust the belt in half turn
increments. Over adjusting the belt can cause damage to the mat.
HOW TO CHECK THE RUNNING BELT FOR PROPER LUBRICATION (PICTURE, P. 7)
Disconnect the main power supply.
Fold the treadmill up into the storage position. Feel the back surface of the running mat.
BELT/DECK/ROLLER LUBRICATION
The mat/deck friction may play a major role in the function and life of your
treadmill and that is why we recommend you constantly lubricate this
friction point to prolong the life time of your treadmill.
You should apply the lubrication after approximately the first 20 hours of
operation. We recommend lubrication of the deck every 30 days.
See below procedures for lubricating:
Use a soft, dry cloth to wipe the area between the belt and deck. Spread lubricant onto the inside surface of belt and deck evenly (make sure
the machine is turned off and power is disconnected).
Periodically lubricate the front and rear rollers to keep them at their peak
performance.
If the treadmill belt/deck/roller is kept reasonably clean it is possible to
expect over 120 hours before additional re-lubing is necessary
BASIC INFORMATION
STARTING AND ENDING WORKOUT
To start the training, press the START/STOP button on the console.
The track will begin to move within 3 seconds of pressing/clicking the Start
button. You may end the workout (stop the track) at any time by pressing/clicking
on Stop.
The track will also stop when the safety key (emergency stop) is
disconnected from the control panel.
SETTING THE SPEED / INCLINATION ANGLE
To change the inclination angle of the treadmill belt, press the I/-
button on the console handle.
To change the speed, press the SPEED +/- buttons on the console handle. Speed adjustment range: 0-16km/h
Adjustment range of the running belt inclination angle: 15 levels
RUNNING BELT
CONTROL PANEL