Spokey 921055, Руководство пользователя

Страница: 8 / 40

8
STEP 4 Connect the bottom parts of side arms (6 l/r) with the handles (7
l/r) using the bolts (35), curved washers (36), and nuts (37).
STEP 5 Pull the wires coming from the counter through the counter base
(49). Mount the counter (50) on the base (49), next connect the wires
coming from the handlebar post with their equivalents coming from the
counter. Put the counter base onto the handlebar post (4).
Levelling, moving the device
Before you start exercising, it is recommended to verify whether the bike is
positioned correctly. Level the equipment with the knobs of the front
stabilizer. To transport the device, raise it carefully on its front wheels
(Figure
– p. 39) and move to another place, holding it on both sides.
Resistance adjustment
The Resistance adjustment function allows to change resistance on the
pedals. High resistance requires larger effort while pedalling, whereas the
low one decreases the effort. Force of resistance is regulated by a knob
placed on the handlebar post. In order to decrease resistance, adjustment
knob should be turned towards the “1“ number whereas so as to increase
resistance, the kno
b should be turned towards the “8” number.
In order to achieve a satisfying effect, resistance level should be set during
a training..
MAINTENANCE

Prior to each use of the bicycle, make sure that all the bolts, nuts and
knobs are tightly fitting.

Aggressive cleaning products must not be used to clean the device. Use
a soft, damp cloth to remove dirt and dust. Clean sweat traces since
acidic pH may damage the upholstery.

The device should be kept in a dry place in order to protect it against
dampness and corrosion.

Should the computer work incorrectly, make sure that all the cables are
connected appropriately, especially the upper cable with the computer. If
the computer still does not work, make sure that batteries have been put
in appropriately and that they are not worn-out. If the readout on the
display screen is not legible or some elements are invisible, replace
batteries immediately.

In case of no resistance adjustment, make sure that the upper sensor
cable is well connected with the lower cable.
CAUTION: Due to the protection of the natural environment, worn-out
batteries, power adapters, motors etc. should not be disposed with
household wastes. Worn-out batteries, power adapters, motors etc. should
be taken to a point that will utilise them in agreement with the enforceable
law on environmental protection. It is recommended to check the power
cord and the plug periodically. Never pull the cord. In case of damage, the
device should not be used. Never repair the device on your own. Repairs
should
be made by a qualified SPOKEY’s company employee.
POWER SUPPLY
Batteries: 1.5V AAA (2 pieces), not supplied with the bicycle
Inserting batteries
1. Insert two batteries at the back of the counter.
2. Make sure that the batteries are correctly positioned.
3. If the display is unreadable or only some segments are visible, remove
the batteries and re-insert them.
4. After removing the batteries, all function values
will be reset.
COUNTER
First start-up
Before the first start-up, make sure that all the cables have been connected
correctly and that the batteries have been inserted correctly.
The display will turn on once you press the button or when you start
pedaling.
Auto on-off
After 4 minutes, the meter enters the energy saving mode. All settings and
data are kept until restarting the meter.
In case the screen does not start, disconnect power supply and wait for 15
seconds.
Device error
If an incorrect reading appears on the counter, remove the batteries and reinsert them.
Button
While touching the button, it allows to select the displaying function. Pressing the button over 3 seconds will reset all functional values to zero
except ODO value
Functions
SCAN: Press MODE button, the arrow will appear and poi
nt to the “SCAN”
position. Then the computer will show all the function one by one. Each
display will be hold for 6 seconds.
SPEED: It shows your pedaling speed on the machine. It starts from 0.00
to 99.9km/h.
CALORIES : it shows how many calories you have burned. It starts from
0.00 to 999.9kcal.
DISTANCE: It shows how many Kilometer or Miles you have worked on the
machine. It starts from 0.00 to 999.9km.
ODO (TOTAL DISTANCE) : It shows the total distance after installing the
batteries
。
It starts from 0.00 to 999.9km.
TIMER: It shows your exercising duration. It starts from 00:00 to 99:59min.
HOW TO OPERATE THE BIKE METER
SCAN
SPEED
DISTANCE
TIME
ODOMETER
CALORIES
PULSE