30
© Titan Tool Inc. All rights reserved.
SAE O-Ring Fitting Installation
Steps 1 & 2:
Step 3:
Step 4:
Step 5:
Cautions:
Lubricate
Lubricate
Tighten nut
Recess
gap
No gap
A
lig
n
Hold
this part
stationay
Avoid screwing fitting in too far.
Avoid leaving fitting too far out.
Bent washer allows
for o-ring extrusion
O-ring cut on
thread
Accessories and Service Kits
These items may be purchased separately from your local
Speeflo distributor.
Part #
Description
103-830
5 Gal. Siphon Hose Assembly w/Rock Catcher
1" x 4.5'
103-808
55 Gal. Siphon Hose Assembly w/Rock Catcher
1" x 6.5'
103-627
Rock Catcher
930-004
Paint Filter Element, 0 Mesh (for mastics)
930-005
Paint Filter Element, 5 Mesh (for multicolors
and heavy materials)
930-006
Paint Filter Element, 50 Mesh (for latex and
normal architectural materials)
930-007
Paint Filter Elements, 100 Mesh (for stains,
lacquers and fine materials)
550-100
S-5 Gun w/Tip
550-110
S-5 Gun, Tip, and 1/4” Hose Kit
101-208
Grounding Clamp
101-212
Grounding Wire, 12 Gauge x 25'
314-480
Piston Lube, 8 oz.
314-482
Liquid Shield Plus, 1 quart
430-362
Coolflo™ Hydraulic Fluid, 1 quart
430-361
Coolflo™ Hydraulic Fluid, 1 gallon
975-212
2-Gun Manifold with Ball Valves, 1/4"
975-213
3-Gun Manifold with Ball Valves, 1/4"
975-312
2-Gun Manifold with Ball Valves, 3/8"
975-313
3-Gun Manifold with Ball Valves, 3/8"
808-550
3/8” NPS(M) x 3” hex fitting
Airless Tip Selection
Tips are selected by the orifice size and fan width. The proper
selection is determined by the fan width required for a specific
job and by the orifice size that will supply the desired amount
of fluid and accomplish proper atomization.
For light viscosity fluids, smaller orifice tips generally are
desired. For heavier viscosity materials, larger orifice tips are
preferred. Please refer to the chart below.
The following chart indicates the most common sizes and the
appropriate materials to be sprayed.
Fan widths measuring 8" to 12" (20 to 30 cm) are most
preferred because they offer more control while spraying and
are less likely to plug.
Tip Size
Spray Material
Filter Type
.011 – .013
Laquers and stains
100 mesh filter
.015 – .019
Oil and latex
50 mesh filter
.021 – .026
Heavy bodied latex and blockfillers
5 mesh filter
NOTE: Do not exceed the pump's recommended tip
size.
1. Pull washer and o-
ring back as far as
possible.
2. Lubricate o-ring and
entrance port.
3. Screw fitting in until
washer pushes o-
ring into entrance
and sits flat against
port. (Do not
tighten! - only do this
step hand tight to
compress o-ring into
port!)
4. Back fitting out no
more than one
complete turn to
align as required.
5. Torque nut wrench
tight holding backup
on fitting. This
should expose a
recess gap behind
the nut which can
act as an indicator
that the fitting is
assembled correctly.
(This is a feature for
a specific version of
this fitting only -
which screws into
the cylinder head.
Other fittings, as the
ones which attach to
the hydraulic pump,
assemble the same
but may not have
the indicator.)
