Spectranetics CVX-300 Скачать руководство пользователя страница 51

Страница: 51 / 56

7030-0068-26

28Jul16

Customer Service, Canada/US (719) 633-8333 / (800) 231-0978

Customer Service, 31 33 434 7050

CVX-300

Excimer Laser System

Version 26

Operator’s Manual

English / English

Troubleshooting: CVX-300 Fault Codes & Error Lamps

Fault

Code

Problem

Description

Try this…

No energy

detected at

detector head

Clean the fiber optic catheter tip and re‑calibrate at the

recommended settings (45/25 for ELCA devices; 60/40

for SLS devices.) Ensure the device is pointed at the

center of the energy detector, one to two inches away.

If calibration is unsuccessful, attempt to calibrate with

the Reference Catheter. If successful, try a new fiber

optic catheter.
If calibration of the Reference Catheter is unsuccessful,

record the Fault code and call Spectranetics

Customer Service.

Calibration

did not occur

within the

unit’s pre‑set

pulse limit
Beam

attenuator

at maximum

opening
Fiber Power

Monitor

test error

Clean the Energy Detector Surface with an alcohol prep.

Clean the fiber optic catheter tip and re‑calibrate at the

recommended settings (45/25 for ELCA devices; 60/40

for SLS devices.) Ensure the device is pointed at the

center of the energy detector, one to two inches away.

If calibration is unsuccessful, attempt to

re‑calibrate the device at a lower fluence

setting (40/25 for ELCA devices; 50/40 for SLS

devices.) If calibration is successful, proceed.

Report the incident to Spectranetics after the

case is complete.

If calibration is unsuccessful, turn the system OFF ( ),

then back ON ( | ). Attempt to calibrate with the

Reference Catheter. If successful, try a new fiber

optic catheter. If calibration of the Reference Catheter

is unsuccessful, record the Fault code and call

Spectranetics Customer Service.

Fiber optic

catheter handle

improperly

inserted

Remove the fiber optic catheter and reinsert. If the fault

is repeated, call Spectranetics Customer Service.

10‑50 System Error

detected

Record the Fault Code and call Spectranetics

Customer Service.

Содержание CVX-300

























































Результаты поиска

Содержание CVX-300

Отзывы:

Бренды по названию

Популярные бренды

Spectranetics CVX-300, Руководство оператора

Результаты поиска

Содержание CVX-300

Отзывы:

Бренды по названию

Популярные бренды