manualshive.com logo in svg

Spectranetics CVX-300, Руководство оператора

Поделиться
Скачать
Spectranetics CVX-300 Скачать руководство пользователя страница 38

38

7030-0068-26

28Jul16

Customer Service, Canada/US (719) 633-8333 / (800) 231-0978

Customer Service, 31 33 434 7050

CVX-300

® 

Excimer Laser System 

Version 26 

Operator’s Manual 

English / English

7. 

Point the distal tip of the fiber optic catheter directly at the center of the energy 
detector. Ensure that the catheter is no less than one inch (2.5 cm) and no more than 
two inches (5 cm) away from the front surface. The red visible beam must be in the 
center of the detector when calibrating.

Warning:

 System faults may occur during the procedure if 

the catheter is not perpendicular to and/or at the proper 
distance from the detector surface during calibration.

8. 

Depress and hold the footswitch down until lasing stops. The Lasing light and red 
lasing status light on the top of the control panel illuminates and the CVX-300 begins 
lasing.
Note: the Power Error lamp may flicker momentarily during the Calibration cycle as 
the laser adjusts energy output (an audible tone will be heard when the Power Error 
lamp illuminates.)

9. 

During the calibration, the display window shows, in the three rightmost digits, the 
energy out of the fiber optic catheter. As the CVX-300 calibrates, the energy out 
of the distal tip of the fiber optic catheter increases or decreases until the energy 
corresponding to the fluence setting for that fiber optic catheter is reached. When the 
calibration is completed, the CVX-300 stops lasing, displays the final calibration energy 
value for approximately five seconds, then returns to the Standby mode, and the Cal 
OK advisory light illuminates. When the calibration is complete, the final calibration 
energy value is visible in the display window.

10. 

Compare the calibration energy reading displayed with the energy range for the fiber 
optic catheter selected. (See catheter package for appropriate ranges.)
NOTE: If the calibration energy at the end of the calibration step was not read, or if 
an energy reading is desired at any other time during the operation of the CVX-300, 
check the energy out of the fiber optic catheter by selecting the Ready mode, depress 
the Read Energy button, aim the distal tip of the fiber optic catheter at the energy 
detector, and depress the footswitch. After reading the energy, depress the Standby 
button to return the CVX-300 to the Standby mode. (Figure 7)

Содержание CVX-300

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды