manualshive.com logo in svg

Spectranetics CVX-300, Руководство оператора

Поделиться
Скачать
Spectranetics CVX-300 Скачать руководство пользователя страница 32

32

7030-0068-26

28Jul16

Customer Service, Canada/US (719) 633-8333 / (800) 231-0978

Customer Service, 31 33 434 7050

CVX-300

® 

Excimer Laser System 

Version 26 

Operator’s Manual 

English / English

Operational Modes

Setup Mode

1. 

Remove the footswitch from the front storage compartment. Close the storage door 
prior to operating the laser. Connect the footswitch plug into the receptacle located 
on the rear panel.

2. 

Connect the end of the power cord into the receptacle located on the lower back panel 
of the CVX-300. Ensure power cord is fully seated into the power receptacle. Insert the 
other end of the power cord into a wall receptacle with the proper output voltage.

Note: Anytime an extension cord is used to power the CVX-300 on a temporary basis, 
it must be a minimum 12 AWG cord of type SJO, SJT, SJOOW or equivalent. The power 
cord should be routed to avoid all tripping hazards and damage from other equipment. 
Any temporary extension cord must be disconnected and removed immediately upon 
completion of the task for which it was installed.

3. 

Insert the key in the keyswitch on the control panel. Turn the keyswitch clockwise to 
activate the system.

4. 

When the system is activated, it enters Testing mode.

5. 

Clean the surface of the energy detector with an alcohol prep before and after each 
use.

Содержание CVX-300

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды