Spectracom VelaSync 1225 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 272

Spectracom VelaSync 1225 Скачать руководство пользователя страница 81

shareware NTP clients are available on the Internet. The software running on the PC
determines whether NTP or SNTP is used.

When the NTP service is enabled, VelaSync will “listen” for NTP request messages from
NTP clients on the network. When an NTP request packet is received, VelaSync will
send an NTP response time packet to the requesting client. Under typical conditions,
VelaSync can service several thousand NTP requests per second without MD5 authen-
tication enabled, and at a somewhat lower rate with MD5 authentication enabled.

You can either enable or completely disable the NTP Service. When NTP is disabled, no
NTP time packets will be sent out to the network. When enabled, by default, the NTP
Service operates in

Unicast

mode, i.e. the NTP Service responds to NTP requests only.

Note:

In order to configure NTP, you need to access the NTP Setup

screen which requires ADMINISTRATOR rights.

2.10.1

Checklist NTP Configuration

The following is a list of configuration settings you may want to consider as you setup
your NTP Service. (Not all items may apply to your application, or there may be other
considerations not included in this list.)

1.

Did you setup your NTP Service and have it use the right

Reference(s)

?

"NTP Reference Configuration" on page 75

2.

Does your NTP Service use the right

Timescale

?

"NTP Output Timescale" on page 73

.

3.

If required, have you setup other

NTP Servers and Peers

for fallback purposes?

"NTP Peers: Adding, Configuring, Removing" on page 79

.

2.10.2 The NTP Setup Screen

The

NTP Setup

screen provides access to all NTP configuration settings.

To open the

NTP Setup

screen, navigate to

MANAGEMENT > NTP Setup

. The

NTP

Setup

screen is divided into 5 panels:

2.10 Configuring NTP

CHAPTER

2

•

VelaSync User's Manual Rev. 3

69

«
...
79
80
81
82
83
...
»

Содержание VelaSync 1225

















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды