Spectracom VelaSync 1225 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 272

Spectracom VelaSync 1225 Скачать руководство пользователя страница 29

1.8

YOUR SAFETY

This product has been designed and built in accordance with state-of-the-art standards
and the recognized safety rules. Nevertheless, its use may constitute a risk to install-
ation/maintenance personnel if used under conditions that must be deemed unsafe, or
if the warnings and precautions explained below are ignored.

Additional Safety Notes pertaining to hardware installation can be found under

Mounting: SAFETY" on page 25

.

1.8.1

SAFETY: Symbols Used

Note:

The following symbols may be found in Spectracom technical

documentation, or on Spectracom products:

Table 1-3:

Spectracom safety symbols

Symbol

Signal word

Definition

DANGER!

Potentially dangerous situation which may lead to per-
sonal injury or death! Follow the instructions closely.

CAUTION!

Potential equipment damage or destruction!
Follow the instructions closely.

NOTE

Tips and other useful or important information.

ESD

Risk of Electrostatic Discharge!
Avoid potential equipment damage by following ESD
Best Practices.

CHASSIS GROUND

This symbol is used for identifying the functional
ground of an I/O signal. It is always connected to the
instrument chassis.

Analog Ground

Shows where the protective ground terminal is con-
nected inside the instrument. Never remove or loosen
this screw!

Recycle

Recycle the mentioned components at their end of life.
Follow local laws.

1.8 YOUR SAFETY

CHAPTER

1

•

VelaSync User's Manual Rev. 3

17

«
...
27
28
29
30
31
...
»

Содержание VelaSync 1225

















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды