manualshive.com logo in svg

Spectracom VelaSync 1225, Руководство пользователя

Поделиться
Скачать
Spectracom VelaSync 1225 Скачать руководство пользователя страница 179

each Email Address field. If desired, the same email address can be used in all of the 
fields, or different addresses can be used for different events.

Note: 

Whether  or  not  notifications  are  enabled/disabled  for  a   given 

event, the occurrence of the event is always logged.

All available VelaSync events  that  can generate a notification to be sent  are located 
under different tabs in the Notification Events panel: 

Timing

, 

GPS

, and 

System

.

The VelaSync Events that can automatically trigger a notification are listed in the 

Event

 

column. It is possible to:

Mask the alarm generation for specific events (prevent the alarm)

Enable “SNMP” (to send out an SNMP trap)

Send an email to the address specified in the corresponding “Email Address” 
column.

4.4.1  

Configuring Notifications

To configure Notifications:

 

1. 

Navigate to 

MANAGEMENT > OTHER: Notifications

. The 

Notifications 

screen 

will display:

It is divided into two panels:

The 

Actions 

panel, featuring:

The 

SNMP Setup

 button: See 

"SNMP" on page 57

.

The 

Email Setup

 button: Configure VelaSync's interface settings for 

Exchange email servers and Gmail.

4.4  Notifications

CHAPTER

4

•

VelaSync User's Manual Rev. 3

167

Содержание VelaSync 1225

















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды