Spectracom VelaSync 1225 Скачать руководство пользователя страница 57

Страница: 57 / 272

2.9.1

General Network Settings

To expedite network setup, VelaSync provides the

General Settings

window, allowing

quick access to the primary network settings.

To access the

General Settings

window:

Navigate to

MANAGEMENT > Network Setup

. In the

Actions Panel

on the left,

click

General Settings

Populate the fields:

Hostname

: This is the server’s identity on the network or IP address.

Default Port

: Unless you specify a specific Port to be used as Default Port,

the factory default port

eth0

will be used as the gateway (default gate-

way).

The

General Settings

window also displays the IPv4 Address and default IPv4

Gateway.

2.9 Configuring Network Settings

CHAPTER

•

VelaSync User's Manual Rev. 3

Содержание VelaSync 1225

















































































































































































































































































Результаты поиска

Содержание VelaSync 1225

Отзывы:

Бренды по названию

Популярные бренды

Spectracom VelaSync 1225, Руководство пользователя

Результаты поиска

Содержание VelaSync 1225

Отзывы:

Бренды по названию

Популярные бренды