Speck XTRAMIX X6 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 21

Speck XTRAMIX X6 Скачать руководство пользователя страница 4

Attaching the mounting brackets for a desktop stand

The mounting brackets can also be used to place the X6 on a desktop and elevate the mixer
above the desk surface at a 10 degree angle as shown in Figure 4.

First attach the 4 protective rubber bumpers to the front face of the brackets - 2 on each
bracket. (See Figure 5).

To attach the brackets place the mixer on a flat surface on its rear connectors (knobs facing
up). Position the bracket on the side of the mixer so the narrow bracket edge faces inward.
Move the bracket around until the 4 mounting holes align with the threaded holes on the
side of the X6.

(4) Black 6-32 Phillips flat head machine screws are needed to attach the 2 rack adapters to
each side for the location of the mounting holes (See Figure 6). Be sure to use all 4 screws
on each side. Note that these are not the same holes used for the 19” configuration.

Attach Rubber

Bumpers Here

Attach with

4 Screws

Figure 4.

Figure 5.

Figure 6.

«
...
2
3
4
5
6
...
»

Содержание XTRAMIX X6






















Отзывы:

Нет отзывов