Specialized KENEVO SL COMP CARBON, Руководство пользователя

Страница: 32 / 51

29
11.2. SHOCK CUSTOMIZATION
Specialized frames are generally designed and tested to work with the suspension
components provided as original equipment. When changing out shocks, be aware certain
models of shocks may not be compatible with the frame due to the position of the shock
reservoir, size, and/or other compatibility factors, even if they fit. Always check with your
Authorized Specialized Retailer for advice on compatible shocks.
WARNING! Use of an incompatible shock may cause damage to the shock or
the frame and can cause you to lose control and fall.
11.3. MAXIMUM FORK LENGTH, TIRE, AND CHAIN-RING SIZE
WHEEL SIZE MAX FORK TRAVEL MAX REAR TIRE SIZE CHAINRING SIZE
29” 170 mm 27.5 x 2.8 or 29 x 2.6 30 - 34t
CAUTION: Different aftermarket wheel/tire and/or fork options may be
available. Note that changing any of these components may affect the bottom
bracket height and head angle of the frame, as well as the general ride
characteristics of the bike. Always check with your Authorized Specialized
Retailer and/or the component manufacturer about compatibility and potential
effects of component changes.
WARNING! Only single crown forks with a specified amount of travel or range
of travel should be used. Use of different styled forks or forks with longer
travel may result in catastrophic failure of the frame which may result in
serious personal injury or death.
WARNING! While the frame is generally compatible with tires up to 29” x 2.6
tire dimensions can vary depending on the manufacturer, and not all forks
are designed to accept a larger tire. Always check with the fork manufacturer
regarding the required clearances.
11.4. TOOLS REQUIRED
„
2, 2.5, 3, 4, 5, 6, 8 mm ALLEN (HEX) KEYS
„
BLUE THREAD-LOCKER (LOCTITE 243)
„
TORQUE WRENCH (reversible type, for SRAM UDH)
„
GREEN RETAINING COMPOUND (LOCTITE 603)
„
HIGH PRESSURE SHOCK PUMP
„
CABLE AND HOUSING CUTTERS
„
HIGH QUALITY GREASE
„
TORX T10, T25, T30 DRIVER
11.5. BOLT SIZE / TOOLS / TORQUE SPECIFICATIONS
WARNING! Correct tightening force on fasteners (nuts, bolts, screws) on your
bicycle is important for your safety. If too little force is applied, the fastener
may not hold securely. If too much force is applied, the fastener can strip
threads, stretch, deform, or break. Either way, incorrect tightening force can
result in component failure, which can cause you to lose control and fall.
Where indicated, ensure that each bolt is torqued to specification. After your
first ride, and consistently thereafter, recheck the tightness of each bolt to
ensure secure attachment of the components. The following is a summary of
torque specifications in this manual:
LOCATION TOOL
TORQUE
(Nm) (in-lbf)
SEAT COLLAR
1
4 mm HEX 6.2
1
55
1
STEM @ STEERER TUBE (TRAIL STEM) 5 mm HEX 5 44
STEM @ HANDLEBAR (TRAIL STEM) 4 mm HEX 5 44
CRANK BOLTS 8 mm HEX 50 443
CHAIN RING BOLTS 5 mm HEX 10 2 89 2
SPIDER BOLT 4 mm HEX 5 44
CHAIN GUIDE 4 mm HEX 3.5 30
WATER BOTTLE CAGE BOLT 3 mm HEX 2.8 25
12 mm REAR AXLE 6 mm HEX 15 133
DERAILLEUR HANGER 8 mm HEX 25 221
HEAD TUBE GUIDE PORT (mounting screw) 2 mm HEX 0.8 7
HEAD TUBE GUIDE PORT (set screw) 1.5 mm HEX NA NA
BATTERY MOUNT BOLT T25 TORX 3 27