SpaNet Power Smart SHP-100 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 23

background image

14

4.6 Three Phase Protection

If the phases are connected in the wrong order due to electrical mis-wiring, this protection
system will interrupt the power supply to prevent damage to the unit. There will be an EE 4
error code on the display.

5. Installation

5.1 Recommended Air Flow Requirements

• The series of heat pumps must be located outside in a clean area where air flow will not
be restrictive. The heat pump must be located external to the spa pool cabinet to allow
sufficient air flow for optimum efficiency.

• The heat pump must operate with a clean air supply so should be situated away from
vegetation and obstacles.

WARNING:

The heat pump MUST be installed according to the air space requirements

shown in Figure 1. Failure to follow these instructions may

VOID WARRANTY.

«
...
12
13
14
15
16
...
»

Содержание Power Smart SHP-100
























Отзывы:

Нет отзывов

Похожие инструкции для Power Smart SHP-100

Бренд: Raypak Страницы: 36

Бренд: wallas Страницы: 43

Бренд: Lasko Страницы: 4

TORNADO 2 Series

Бренд: Larius Страницы: 32

Elmo Rietschle V-VC 40

Бренд: Gardner Denver Страницы: 32

Бренд: Carrier Страницы: 30

Omnivore XLSG200 Series

Бренд: Liberty Pumps Страницы: 12

BLACKLIGHT 7815

Бренд: MO-EL Страницы: 12

Бренд: veito Страницы: 24

Бренд: Vasco Страницы: 32

Бренд: Warmtec Страницы: 60

Бренд: N'oveen Страницы: 66

Бренд: DAYLIFF Страницы: 8

Бренд: Malmbergs Страницы: 12

Бренд: Vornado Страницы: 9

Бренд: Eaton Страницы: 21

Бренд: Dimplex Страницы: 44

Бренд: Liebert Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды