background image

• The solenoids provided in the SHAVED40 kit can be mounted horizontally or 

vertically (with the plunger UP) to the door with the provided hardware.

• Attach the solenoid to the door latch with the supplied cable and cable crimp.

-Loop the cable through the solenoid and the door latch and crimp the two ends 
together with the cable crimp.

Solenoid Wiring:

• Attach the white wire of the 

Driver Door

Solenoid to the Brown wire (large 

gauge/channel 1, from spade connector harness) of the receiver.

• Attach the white wire of the 

Passenger Door

Solenoid to the Yellow wire (large 

gauge/channel 2, from spade connector harness) of the receiver

• Connect the remaining black wire of the solenoid to a ground located on the 

vehicle body.  (The door is not a proper grounding source!)

**A mechanical backup switch should be utilized in the case of power failure.  (See the 

optional wiring section)**

4

Mounting / Wiring Section

5

Receiver Mounting and Wiring:

**The receiver must be mounted inside the vehicle to avoid moisture**
***Do not plug in the receiver module until all the wiring is complete!***
***Do Not Ground the Antenna!***

ANTENNA

NOT USED

NOT USED

+12 VOLTS DC

CH1 OUTPUT (+)

CH2 OUTPUT (+)

SEE TABLE

DIP SWITCHES

PROGRAMMING BUTTON

LED

JUMPERS

MOLEX CONNECTOR

SPADE CONNECTORS

Notes:

*Connecting the YELLOW (ignition) wire will disable Channels 1-4 while the ignition key is ON.

**Whan installing a SHAVED ACT Kit replace the 35 Amp fuse with the supplied 10 Amp fuse

The unit will stop operating for 30 seconds if any combination of the Remote Control
Buttons 1 and/or 2 are pressed eight (8) times in 30 seconds.  After 30 seconds the unit
will automatically reset to standard operating mode.

Mounting / Wiring Section

Molex Connector

Spade Connectors

Pin #

Wire Color

Circuit

Wire Color

Circuit

1

Black

Ground

Violet

Not Used

2

Not Used

Not Used

Orange

Not Used

3

Purple

Channel 7

Red

Positive 12 VDC**

4

Blue

Channel 5

Brown

Channel 1 

5

Orange

Channel 3

Yellow

Channel 2

6

Red

Positive 12 VDC

7

Yellow

Ignition*

8

Not Used

Not Used

9

White/Black

Channel 6

10

Brown

Channel 4

Brown or Yellow 
Wire of Receiver

Black: Connect 
to ground

CABLE CRIMPS

1.25" MAXIMUM 

EXTENSION

DOOR LATCH 
MECHANISM ARM

Содержание SHAVED-B

Страница 1: ...EP YOUR INVOICE WITH THIS WARRANTY STATEMENT 10 04 8 Trouble Shooting Reverse Polarity Wiring Problems Switch doesn t work properly but the shaved kit transmitters do work Step 1 Did you purchase a switch kit designed for three switches and only use two switches YES Connect third switch NO Check wiring Switch works properly but shaved kit transmitters do not work Step 1 Does the LED on the remote ...

Страница 2: ...ceiver 2 Remotes 2 Wire Harnesses Installation Instructions for SPAL Shaved Door Handle Kit Shaved 40 This kit is designed to operate up to seven functions via the four button remote control Channels 1 and 2 are Positive outputs used to open your drivers and passenger doors Channels 3 through 7 are all negative outputs tht can be used ot operate power door locks power door releases truck releases ...

Страница 3: ...le to avoid moisture Do not plug in the receiver module until all the wiring is complete Do Not Ground the Antenna ANTENNA NOT USED NOT USED 12 VOLTS DC CH1 OUTPUT CH2 OUTPUT SEE TABLE DIP SWITCHES PROGRAMMING BUTTON LED JUMPERS MOLEX CONNECTOR SPADE CONNECTORS Notes Connecting the YELLOW ignition wire will disable Channels 1 4 while the ignition key is ON Whan installing a SHAVED ACT Kit replace ...

Страница 4: ...ed outside the vehicle in the case of lost transmitters or keys locked in the vehicle 6 Y T BA TE R DO NOT GROUND INSIDE THE DOOR Optional Wiring Section Item to be Description Relay Type of Relays Diagram Activated of Function Required 1 Power window motor Move window up down SPDT 2 Reverse 1 Power window motor Move window one direction SPDT 1 Reverse Linear actuator Move in out SPDT 2 Reverse So...

Отзывы: