1
2
4
3
Reprogramming the Remote Transmitters:
**This Shaved Door kit can accept up to 4 SPAL remote transmitters
(Part #MULTI-RCU7TX)
**
The remote transmitters are shipped Pre-Programmed. In the event that a remote
transmitter loses the programmed code, or if you wish to add more remote
transmitters, follow these instructions:
• Make sure ignition is OFF.
• Locate the programming button located on the side of the receiver, next to the LED.
• Press the programming button 3 times quickly (The LED will light).
• Press Button (1) on each transmitter you want learned in to the receiver (one at a time).
There is a 10 second window to learn all new transmitters.
• The LED will remain lit for approximately 10 seconds after the last remote transmitter has
been recognized.
• Wait for the LED to go out. Then test each remote transmitter for proper function.
Jumper Settings:
To avoid damage to attached components,
the jumpers must remain in the factory setting.
To Operate:
Press:
Channel 1
Button 1
Channel 2
Button 2
Channel 3
Button 3
Channel 4
Button 4
Channel 5
Button 1 + Button 2
Channel 6
Button 1 + Button 3
Channel 7
Button 1 + Button 4
Basic Function of the SPAL Shaved Door Kit
The remote control supplied with your kit has four buttons, but is capable of controlling
7 channels.
Channel 1: +12VDC
Opens drivers door
Channel 2: +12VDC
Opens passenger door
Channel 3:
Channel 4:
Channel 5:
Channel 6:
Channel 7:
Operation Section
Programming Section
3
Basic Functions Of The Remote Control
Emergency/Backup Switch (not included in kit):
It is strongly recommended that an emergency/backup switch be mounted outside the
vehicle in the case of lost transmitters or keys locked in the vehicle.
6
Y
T
BA TE
R
DO NOT GROUND INSIDE THE DOOR
Optional Wiring Section
Item to be
Description
Relay Type # of Relays Diagram
Activated
of Function
Required
1 Power window motor
Move window up & down
SPDT
2
Reverse
1 Power window motor
Move window one direction
SPDT
1
Reverse
Linear actuator
Move in & out
SPDT
2
Reverse
Solenoid
Activate Solenoid
SPST
1
Positive or Negative
Trunk Release
Open the Trunk
SPST
1
Positive or Negative
Door lock actuator
Lock & unlock
SPDT
2
Reverse
SPST
= Single pole single throw relay, 30 or 40 amp
SPDT
= Single pole double throw relay 30 or 40 amp
Relays can either be purchased from SPAL USA or from your local auto parts store.
If The Control Unit Is Connected To:
Dip Settings*
Solenoids
1-2:
Off
3-7:
Off
Actuators
1-2:
On
3-7:
Off
Optional Mechanical Backup Cable
(HR-Entry)
4
3
5 6 7 8
ON
1 2
DIP SWITCHES
A mechanical backup cable
should be utilized in all shaved
door applications.
By using a mechanical
backup, you do not run the risk
of being locked out of the vehicle
if the battery were to go dead.
SPAL USA offers a universal
mechanical cable
(part #HR-ENTRY) that can be run
to a concealed location, such as
the front wheel well.
Dip Switch Settings:
Wiring Options
Power Wire
Ground Wire
Drivers Door
Grey wire of Control Unit
Chassis Ground
Passenger Door
Green wire of Control Unit
Chassis Ground
Inside Button Option:
Internal Buttons: If you wish to remove the door handles from inside the vehicle and
use power buttons, you will need to wire the buttons as follows:
Optional negative outputs (250 mA)
**Additional relays are required for each channel**
(See Page 7 For Wiring Diagrams)
* Switches 3-8 will always be in the
OFF
position
**12 Gauge
Wire Must
Be Used**
