Spacerails LEVEL 4 Скачать руководство пользователя страница 5

Страница: 5 / 16

Page 5

Step 3:

Once the Corkscrew is

built, attach three support shafts

(300mm) to the Power Box.

ELEVATOR ASSEMBLY

Step 2:

Connect Elevator Helix

pieces together with the male part

facing up to fill the shaft.

NOTE:

Install the first Elevator

Helix piece male side

up and rotate it until

it slides in place and

engages with driver at

the base of Power Box.

Step 1:

Place a shaft in the

white hole on the Power Box.

Step 6:

Place the Elevator Cover

onto the top of the elevator

assembly.

Step 7:

Attach an Elevator Guard to

each of the Elevator Rings, then to

the right side of the Rail Clip.

Step 5:

Place the three Elevator

Rings over the three shafts.

NOTE:

The Marble may fall

out of the elevator if it

enters too fast.

Step 4:

Connect

one Rail Clip to each

Elevator Ring. Install

Elevator Ring with

tabs facing up, as

shown above.

Содержание LEVEL 4

















Результаты поиска

Содержание LEVEL 4

Отзывы:

Похожие инструкции для LEVEL 4

Бренды по названию

Популярные бренды

Spacerails LEVEL 4, Быстрый старт

Результаты поиска

Содержание LEVEL 4

Отзывы:

Похожие инструкции для LEVEL 4

Бренды по названию

Популярные бренды