Spacerails LEVEL 4 Скачать руководство пользователя страница 13

Страница: 13 / 16

Page 13

INSTALL RAILS B, C, AND D

Step1:

Starting at the top center Elevator Ring (2R-1) connect Rail B (5 cm) to Rail Clip. Connect the other

end to the Rail Splitter. The Rail Splitter will not be held up by a shaft.

Step2:

Connect Rail C (45 cm) to the right side of the Rail Splitter. Curve the rail and Connect to L-6, then

O-6, then P-4. Rail will end above the two See-Saws. You can use a Marble to adjust the See-Saws. The

Marble should fall onto each See-Saw Arm and tip the See-Saw forward, falling onto the one beneath it.

Step 3:

Connect Rail D (200 cm) to the left part of the Rail Splitter. Continue rail to D-6 and curve around

to connect to C-3. Continue in a downward slope to J-1, then loop rail and attach to K-2 then K-1.

Step 4:

Continue rail in a curve and attach to L-4, then I-3. Curve rail the opposite way and connect to

G-2, under the Start Block, and finish at Elevator Exit R-3.

Rail B, C, and D

See-Saws

Seesaw

Elevator Exit

Elevator Entry

Содержание LEVEL 4

















Результаты поиска

Содержание LEVEL 4

Отзывы:

Похожие инструкции для LEVEL 4

Бренды по названию

Популярные бренды

Spacerails LEVEL 4, Быстрый старт

Результаты поиска

Содержание LEVEL 4

Отзывы:

Похожие инструкции для LEVEL 4

Бренды по названию

Популярные бренды