Spacerails LEVEL 4 Скачать руководство пользователя страница 3

Страница: 3 / 16

Page 3

ARM ASSEMBLY

(QTY: 66 SHAFT TO RAIL)

RAIL SPLITTERS

PREPARE THE COASTER COMPONENTS

Step 1:

Attach one Arm Holder A and one

Arm Holder B with one Arm Sheath.

Step 2:

Insert one Arm Clip into Arm

Holder A. Slide the circular part between

the matching parts on the Arm Holder.

Step 1:

Attach one Rail Clip on each of

the Rail Splitter posts.

Step 4:

Turn the Arm Lock

counter-clockwise to secure the

Arm Clip in place.

Step 3:

Insert Arm Lock through Arm

Holder A and Arm Clip. Ensure that the

tab is facing up.

To avoid damaging parts, do not move or adjust the Rail Clip while locked in the arm. To move the Rail Clip, release

Arm Lock by turning clockwise, position Rail Clip as desired, then secure Arm Lock again.

NOTE:

The hole shapes of the Arm Holder

and Arm Sheath differ.

Arm Holder B

Arm Holder A

Содержание LEVEL 4

















Результаты поиска

Содержание LEVEL 4

Отзывы:

Похожие инструкции для LEVEL 4

Бренды по названию

Популярные бренды

Spacerails LEVEL 4, Быстрый старт

Результаты поиска

Содержание LEVEL 4

Отзывы:

Похожие инструкции для LEVEL 4

Бренды по названию

Популярные бренды