manualshive.com logo in svg

SP VirTis BenchTop 2K, Руководство оператора

Поделиться
Скачать
SP VirTis BenchTop 2K Скачать руководство пользователя страница 38

Cold Trap Condenser 

VirTis BenchTop 2K, 4K and 6K 

 
 

28 

 

Revision 004, 12/09 

Cold Trap Setup 

The following instructions will help you utilize your BenchTop as a cold trap to 
condense vapors from a gel dryer or vacuum concentrator: 

1.

 

Position the vacuum concentrator, BenchTop and vacuum pump in a 
convenient location with sufficient space to easily connect the units. 

2.

 

Place the vacuum cover plate (acrylic plate with stainless steel elbow) on the 
gasket of the BenchTop unit. 

3.

 

Connect the BenchTop unit to the vacuum concentrator using ¾-inch tubing. 

4.

 

Estimate the length of tubing required to adequately reach the back of the 
vacuum concentrator without any tension.  

5.

 

If necessary cut the tubing to the proper length and secure both ends with 
tubing clamps. 

6.

 

Connect the vacuum pump to your BenchTop unit as described in Chapter 2: 
Installation and Setup.  

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

© SP Industries, Inc. 2009 

Содержание VirTis BenchTop 2K

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды