manualshive.com logo in svg

SP VirTis BenchTop 2K, Руководство оператора

Поделиться
Скачать
SP VirTis BenchTop 2K Скачать руководство пользователя страница 26

Sentry 2.0 Controls 

VirTis BenchTop 2K, 4K and 6K 

 
 

16 

 

Revision 004, 12/09 

 

 

© SP Industries, Inc. 2009 

Alarms Menu 

The Alarms screen displays all active alarms. A shaded box appears in front of 
triggered, active alarms. You can also accept and clear triggered alarms from this 
screen. To clear an alarm, use the 

Up/Down (+/-) 

buttons to highlight the desired 

alarm and press the 

MENU

 button. Before the alarm will clear, the condition that 

caused the alarm must be resolved.

 

 

 

 

 

 

∧

    Alarms 

 

_ Power Outage 

_ Condenser Over Temperature 

_ Vacuum Exceeded 

_ Vacuum Pump Maintenance 

 

Menu To Clear 

Setpoints Menu 

To edit setpoint values, use the 

Up/Down (+/-) 

buttons and highlight the desired field. 

Press and hold the 

MENU 

button until prompted to adjust the value. Adjust the value 

with the 

Up/Down (+/-) 

buttons and press the 

MENU

 button to enter the setpoint. 

 

∧

    Setpoints 

 
Condenser Temperature  -60 
Vacuum OK              0500 
Power Save Deadband    050 
 
 

PRESS AND HOLD MENU BUTTON TO ADJUST 

Condenser Temperature 

The Condenser Temperature setpoint is the temperature at which the vacuum will 
energize in auto mode. The Condenser Over Temperature alarm is also referenced 
from this value. The alarm will be triggered when: (1) the condenser temperature rises 
more than 10 °C above the setpoint temperature after obtaining the setpoint at least 
once, and (2) the condenser is unable to obtain the setpoint after 30 minutes of 
starting an automatic cycle. 

Vacuum OK  

Vacuum OK is the pressure setpoint at which the Vacuum Exceeded alarm will be 
generated. There is a 30-minute delay in the Vacuum Exceeded alarm to allow flasks 
to be added to the system without generating this alarm. 

Power Save Deadband 

The Power Save Deadband is the acceptable amount of pressure rise within the 
system before the vacuum pump is re-energized. This value is used when Vacuum 
Control is set to Power Save in the User Options screen. 

Содержание VirTis BenchTop 2K

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды