SP VirTis BenchTop 2K Скачать руководство пользователя страница 22

Страница: 22 / 56

Sentry 2.0 Controls

VirTis BenchTop 2K, 4K and 6K

Revision 004, 12/09

Vacuum

The LEDs on the top wave represent the following vacuum setpoints:

LED

Vacuum (mTorr)

Color

1 2000

Red

2 1000

Red

3 500

Amber

4 200

Amber

5 100

Green

6 50

Green

≤

Green

Button Functions

Up/Down (+/-) Buttons

The

Up/Down (+/-)

buttons allow you to navigate the menus and increase or decrease

setpoint values displayed on the LCD display.

MENU Button

The

MENU

button performs a number of functions. During an alarm condition,

pressing the

MENU

button will temporarily silence (but not clear) the alarm. When

viewing the Synoptic screen, the

MENU

button will display the Main Menu.

The

MENU

button also acts as an enter key, activating the selected option. To return

to a previous menu, highlight the carat (

∧

) at the top left corner of the LCD screen and

press the

MENU

button.

COND Button

The

COND

button activates the refrigeration system. This provides system cooling for

vapor condensing.

VAC Button

The

VAC

button enables the vacuum pump and opens the vacuum brake solenoid

(VBS) valve, allowing the system to be evacuated. Vacuum level control options can
be programmed from the User Options screen.

Note:

If your vacuum pump is not connected to the IEC plug on the rear of the BenchTop unit,

the

VAC

button will not control your pump. See your pump manual for operation instructions.

AUTO Button

The

AUTO

button will start the refrigeration and vacuum systems in a set sequence.

The condenser will first cool to the condenser setpoint. Once the setpoint is achieved,
the vacuum pump will energize and begin evacuating the system.

DEFR Button

The

DEFR

button activates the condenser defrost function. Hot gas defrost is directed

toward the condenser walls to quickly loosen ice.

Note:

Defrost mode is disabled while any other function is on.

Содержание VirTis BenchTop 2K

























































Результаты поиска

Содержание VirTis BenchTop 2K

Отзывы:

Бренды по названию

Популярные бренды

SP VirTis BenchTop 2K, Руководство оператора

Результаты поиска

Содержание VirTis BenchTop 2K

Отзывы:

Бренды по названию

Популярные бренды