southpaw enterprises In-FUN-ity Climbing System, Инструкция

Страница: 6 / 23

southpaw enterprises, inc.
®
Instruction Sheet
In-FUN-ity Wall Ladder - Metal Stud Wall 152001
Store these instructions along with the enclosed maintenance checklist
in a safe place. You may also access them on our website.
Take time to familiarize yourself with the use and maintenance of this equipment before using. Please file
this Instruction Sheet in an accessible location: the Instruction Sheet must be read and familiar to anyone
who is using Southpaw Enterprises Equipment.
IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping.
If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately.
MATERIALS LIST:
1 - Ladder Top Section 1 - Hardware Kit Containing:
1 - Ladder Bottom Section 4 - 1/4” x 3” Toggle Bolt Anchors
4 - Connector Screws 4 - 1/4” Fender Washers
1 - 5/32” Hex Key 4 - 1/4” Internal Tooth Lock Washers
1 - Instruction Sheet
1 - Maintenance Checklist
ASSEMBLY:
Position the top and bottom sections of the ladder on the floor with the screw holes in the bottom of the top section fac-
ing up as shown at right.
Check that you have all the holes aligned. Start the screws into the pilot holes and tighten all of them securely using
the hex key provided.
ATTACHING TO WALL:
The Therapy Ladder Wall has four slots where the toggle bolts attach the ladder to the wall. They are positioned to
accommodate studs on 16” or 24” centers. Position the assembled Therapy Ladder Wall against the wall where you
wish to install it. Make sure that there are no obstructions such as electric outlets interfering with installation. Locate
two adjacent studs where you want to put the ladder. This can be accomplished using a stud finder tool. Mark the
center of both studs at 20-1/2” and 68-1/2” from the floor.
Note: it is very important to make your mark at the exact
center of the studs. Failure to do this will result in diminished holding power of the toggle bolts. This could
cause the unit to become detached from the wall resulting in injury to users. Drill an 11/16” hole into the studs at
each of the marks. Reposition the ladder on the wall and align the slots with the holes. Remove the toggle “wings”
from the four bolts.
MAINTENANCE CHECKLIST:
All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed.
•
Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they
are tightened.
•
Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact
Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer.
TOP SECTION
BOTTOM SECTION
SCREWS
MATERIALS LIST:
1 - Ladder Top Section 1 - Hardware Kit Containing:
1 - Ladder Bottom Section 4 - 1/4-20 Toggle Bolt Anchors
4 - Connector Screws 8 - 1/4” Fender Washers
1 - 5/32” Hex Key 4 - 1/4” Internal Tooth Lock Washers
1 - Instruction Sheet
1 - Maintenance Checklist
ASSEMBLY:
Position the top and bottom sections of the ladder on the floor with the screw holes in the bottom of the top section fac-
ing up as shown at right.
Check that you have all the holes aligned. Start the screws into the pilot holes and tighten all of them securely using
the hex key provided.
ATTACHING TO WALL:
Position the assembled Therapy Ladder Wall against the wall where you wish to install it. Make sure that there are no
obstructions such as electric outlets interfering with installation.
The Therapy Ladder Wall has two sets of slots in each of the mounting boards. These will accommodate mounting to
studs set on either 16” or 24” centers. Using a stud finding tool, locate two adjacent studs where you want to mount
the ladder. Mark the center of these studs 20-1/2” and 68-1/2” from the floor.
Note: it is very important to make
your mark at the exact center of the studs. Failure to do this will result in diminished holding power of the tog-
gle bolts. This could cause the unit to become detached from the wall resulting in injury to users. Drill an
11/16” diameter hole through the wall and the studs at each of the marks.
Remove the “wings” from the toggle bolts and put one internal tooth lock washer then two fender washers on each bolt.
Put the bolts through the proper slots in the mounting boards then screw the wings onto the bolts making sure that the
wings fold back toward the head of the bolt.
Reposition the ladder on the wall and align the bolts with the holes. Push on the bolts until the wings fold back and go
through the hole in the wall and the stud. After pushing all four bolts into the holes, use a screwdriver to tighten each
bolt securely.
MAINTENANCE CHECKLIST:
All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed.
•
Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they
are tightened.
MATERIALS LIST:
1 - Ladder Top Section 1 - Hardware Kit Containing:
1 - Ladder Bottom Section 4 - 1/4-20 Anchors
6 - 3/8-16 x 1-1/2” Button Head Cap Screws 8 - 1/4” Fender Washers
6 - 3/8” Flat Washers 4 - 1/4” Internal Tooth Lock Washers
1 - 7/32” Hex Key 4 - 1/4-20 x 1-3/4” Hex Head Cap Screws
1 - Instruction Sheet
1 - Maintenance Checklist
ASSEMBLY:
Position the top and bottom sections of the ladder on the floor with the wall attachment boards on the floor. Position
the top and bottom so that the three bolt holes in the bottom of the top section will be aligned with the three t-nuts in the
top of the bottom section. Slide the top section into the bottom section as shown in picture at right. Be sure that the
head of the screw holding the ladder rung slides into groove in the bottom section. Align the bolt holes with the t-nuts.
Place a 3/8” flat washer on each of the 3/8 x 1-1/2” bolts. Start the bolts from the inside, through the holes in the top
section and screw it into the t-nut in the bottom section.
ATTACHING TO WALL:
Position the assembled Therapy Ladder Wall against the wall where you wish to install it. Make sure that there are no
obstructions such as electric outlets interfering with installation.
Make a mark on the wall in the center of each of the four outside slots. This will determine where to drill for the an-
chors. Remove the ladder from the wall. Using a power drill and a 1/2” diameter masonry bit, drill a hole as deep as
the length of the anchor into the wall at each of the four marks. Vacuum the dust from the holes and insert the anchors
until they are flush with the wall. Reposition the ladder on the wall and align the slots with the holes. Put one internal
tooth lock washer then two fender washers on each bolt. Start a bolt into each of the anchors and tighten securely.
MAINTENANCE CHECKLIST:
All of the following wear points should be checked on a monthly basis and recorded on the checklist enclosed.
•
Check that all screws and bolts are tight. If any screws or bolts are found to be loose, discontinue use until they
are tightened.
•
Check wood surfaces for cracks and splinters. If cracks are found, discontinue use immediately and contact
Southpaw Enterprises. Splinters may be sanded smooth and refinished with clear lacquer.
TOP
BOTTOM
T-NUTS
GROOVE FOR SCREW HEAD
MATERIALS LIST:
1 - Ladder Top Section (6 rungs) 1 - Hardware Kit Containing:
1 - Ladder Bottom Section (4 rungs) 4 - 1/4 x 3” Toggle Bolt Anchor
6 - 3/8-16 x 1-1/2” Button Head Cap Screws 8 - 1/4” Fender Washers
6 - 3/8” Flat Washers 4 - 1/4” Internal Tooth Lock Washers
1 - 7/32” Hex Key
1 - Instruction Sheet
1 - Maintenance Checklist
The In-FUN-ity Climbing System is a modular system. Each instruction sheet is designed to assist you in assembling
the particular item that it accompanies. Since these items may be configured in various manners to best suit your appli-
cation, the instructions do not suggest any particular order of assembly. If you have any questions about how to set up
your system, please contact Southpaw customer service for help.
WORKING LOAD: 250 lbs.
ASSEMBLY:
Place the top and bottom sections of the
ladder on the floor with the wall attachment
boards on the floor. Position the top and
bottom so that the three holes in the bot-
tom of the top section will be aligned with
the three t-nuts in the top of the bottom
section.
Slide the top section into the bottom sec-
tion as shown in fig. 1. Be sure that the
head of the screw holding the ladder rung
slides into groove in the bottom section.
Align the bolt holes with the t-nuts.
Place a 3/8” flat washer on each of the
3/8 x 1-1/2” bolts. Start the bolts from the
inside, through the holes in the top section and screw it into the t-nut in the bottom section. Start all six bolts then tighten
securely with the hex key wrench provided.
ATTACHING TO WALL:
Position the assembled Therapy Ladder Wall against the wall where you wish to install it. Make sure that there are no
obstructions such as electric outlets interfering with the installation.
The Therapy Ladder Wall has two sets of slots in each of the mounting boards. These will accommodate mounting to
studs with either 16” or 24” centers. Using a stud finding tool, locate the two adjacent studs to which you want to mount
the ladder. Mark the center of these studs 20-1/2” and 68-1/2” from the floor.
Note: it is very important to make your
mark at the exact center of the studs. Failure to do this will result in diminished holding power of the toggle
bolts. This could cause the unit to become detached from the wall resulting in injury to users.
TM
TOP
BOTTOM
T-NUTS
GROOVE FOR SCREW HEAD
Fig 1.