Exterior Lightbar Connect-n-Go System
nROADS Connect-n-Go 1018
7.
Initial Setup of mpower® Fascia Lights (2 Front and 2 Rear):
The Connect-n-Go mpower® modules will automatically sync with the nROADS® Fleet Lightbar. To ensure the mpower® modules are synced
properly based upon where they are mounted, perform the following steps:
1. Ensure the lightbar is powered properly and no buttons are activated on the handheld.
2. Connect the first mpower® module (mounted on the Rear Driver side of the vehicle) to one of the mating connector harnesses coming out of the
lightbar.
3. Activate a button on the handheld, deactivate the button, and then wait for the system to recognize the newly plugged in module (about 15
seconds.) The module will flash its ID when it has paired with the lightbar.
4. Connect the next module and repeat steps 2 - 3 (in the order shown below) for each module until all modules have been paired, where the
mpower® module with:
a. ID #1 is in the Rear Driver position.
b. ID #2 is in the Rear Passenger position.
c. ID #3 is in the Front Driver position.
d. ID #4 is in the Front Passenger position.
5. If an mpower® module is not acting as desired, refer to Program 6, 7, 8, or 9 on Pages 10, 11 for reprogramming steps.
Initial Setup of mpower® Fascia Lights (2 Rear):
The Connect-n-Go mpower® modules will automatically sync with the nROADS® Fleet Lightbar. To ensure the mpower® modules are synced
properly based upon where they are mounted, perform the following steps:
1. Ensure the lightbar is powered properly and no buttons are activated on the handheld.
2. Connect the first mpower® module (mounted on the Rear Driver side of the vehicle) to one of the mating connector harnesses coming out of the
lightbar.
3. Activate a button on the handheld, deactivate the button, and then wait for the system to recognize the newly plugged in module (about 15
seconds.) The module will flash its ID (1) when it has paired with the lightbar.
4. Connect the second mpower® module (mounted on the Rear Passenger side of the vehicle) to the remaining mating connector harness coming
out of the lightbar.
5. Activate a button on the handheld, deactivate the button, and then wait for the system to recognize the newly plugged in module (about 15
seconds.) The module will flash its ID (2) when it has paired with the lightbar.
6. If an mpower® module is not acting as desired, refer to Program 6, 7, or 8 on Page 10 for reprogramming steps.
Initial Setup of mpower® Fascia Lights (2 Front):
The Connect-n-Go mpower® modules will automatically sync with the nROADS® Fleet Lightbar. To ensure the mpower® modules are synced
properly based upon where they are mounted, perform the following steps:
1. Ensure the lightbar is powered properly and no buttons are activated on the handheld.
2. Connect the first mpower® module (mounted on the Front Driver side of the vehicle) to one of the mating connector harnesses coming out of
the lightbar.
3. Activate a button on the handheld, deactivate the button, and then waiting for the system to recognize the newly plugged in module (about 15
seconds.) The module will flash its ID (3) when it has paired with the lightbar.
4. Connect the second mpower® module (mounted on the Front Passenger side of the vehicle) to the remaining mating connector harness coming
out of the lightbar.
5. Activate a button on the handheld, deactivate the button, and then waiting for the system to recognize the newly plugged in module (about 15
seconds.) The module will flash its ID (4) when it has paired with the lightbar.
6. If an mpower® module is not acting as desired, refer to Program 6, 7, or 8 on Page 10 for reprogramming steps.
ELECTRICAL INSTALLATION (CONT.)
