Exterior Lightbar Connect-n-Go System
nROADS Connect-n-Go 1018
11.
FLASH PATTERNS & CONFIGURATIONS (CONT.)
Program 7 – mpower® Fascia Flash Front Colors Selection:
1. Press and hold buttons 2 and 4 for 5 seconds.
2. The arrow left, arrow right, and alley left indicators will flash and system will transition to warning mode to indicate system is in this programming mode.
3. Press button 7 to assign settings to flash pattern 1. Press button 8 to assign settings to flash pattern 2.
4. The front aux light flash pattern colors are selected by buttons 1, 2 and 3, where button 1 will enable color 1, button 2 will enable color 2, and button 3 will
enable color 3. Dual color flash mode is activated when two aux buttons are selected.
5. Color swap of dual color patterns is enabled with button 4 for the front mpower® lights. This will swap the color flash phase with respect to the lightbar.
6. Press the front button to exit programming mode, rear to decrement to the previous program mode or full to advance to next programming mode.
Program 8 – mpower® Fascia Flash Rear Colors Selection:
1. Press and hold buttons 2 and 5 for 5 seconds.
2. The arrow right, alley left and alley right indicators will flash and system will transition to warning mode to indicate system is in this programming mode.
3. Press button 7 to assign settings to flash pattern 1. Press button 8 to assign settings to flash pattern 2.
4. The rear aux light flash pattern colors are selected by buttons 1, 2 and 3, where button 1 will enable color 1, button 2 will enable color 2, and button 3 will
enable color 3. Dual color flash mode is activated when two aux buttons are selected.
5. Color swap of dual color patterns is enabled with button 4 for the rear mpower® lights. This will swap the color flash phase with respect to the lightbar.
6. Press the front button to exit programming mode, rear to decrement to the previous program mode or full to advance to next programming mode.
Program 9 – mpower® Position Selection:
1. Press and hold buttons 2 and 6 for 5 seconds.
2. All lights will turn off, except one of the mpower® lights will turn on steady for color 1. Buttons 1, 3, 4, and 6 will either blink or turn on solid. The solid LED
represents the current position of the active module, where button 1 = Driver Front, button 3 = Passenger Front, button 4 = Driver Rear, and button 6 =
Passenger Rear.
3. Press the right arrow button to advance which mpower® module is lit (the left arrow will go backwards.)
4. Select the corresponding button to assign the lit light to a position. If that position already had a light assigned, that light will swap positions of the currently lit
light. For example: The mpower® module in the passenger rear is lit and button 1 is solid; the light was assigned improperly. Pressing button 4 will assign the
light module to the Driver Rear; the light that was in the Driver Rear position is now assigned to Driver Front.
5. If desired, press button 2 or 5 to set the lit module to be unassigned. Now, buttons 1, 3, 4, and 6 will all flash to indicate that the active light is not assigned to
any of the positions. When in operating mode, an unassigned module will not flash.
6. Press the front button to exit this mode.
7. Verify placement by activating the front and then rear buttons and observing the lights.
Factory Reset:
1. Press and hold buttons 1, 2, and 3 for 5 seconds.
2. The arrow left, arrow right, alley left, and alley right red indicators will flash.
3. Press the FRONT button within 2 seconds of the alley / arrow indicators flashing to reset settings.
HANDHELD BUTTON ASSIGNMENT
(PROGRAMMING MODE)
Button
Function
Front
Exit Programming Mode
Rear
Return to Previous Programming Mode
Full
Advance to Next Programming Mode
Flash 2*
Button 1
Front Scene
Button 2
Full Scene
Button 3
Alley Left
Button 4
Rear Work
Button 5
Alley Right
Button 6
Arrow Left
Button 7
Arrow Right
Button 8
*Flash must already be active
Note: Cannot flash tri-color.
