Exterior Lightbar Connect-n-Go System
nROADS Connect-n-Go 1018
1.
TABLE OF CONTENTS
PAGE CONTENT
1
COMPONENTS/ CONTENTS
2
MODULE SPECIFICATIONS
3
TECHNICAL/ POWER SPECIFICATIONS
4 FIXED HEIGHT BRACKETS AND HOOK MOUNTING
5 GASKET MOUNTING INSTRUCTIONS
6,7 ELECTRICAL INSTALLATION
8,9 MPOWER® INSTALLATION
10-12 FLASH PATTERNS & CONFIGURATIONS
13 WIRING & HANDHELD BUTTON ASSIGNMENT
14 LIGHT MODULE WIRE HARNESS LOCATIONS
15 DRIVER MODULE/ MPOWER® REPLACEMENT
16 CONNECT-N-GO SYSTEM TROUBLESHOOTING
17,18 REPLACEMENT PARTS
19 WARRANTY AND RETURN GOODS PROCEDURE
Important Information:
!
WARNING
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
COMPONENTS/ CONTENTS
Standard Equipment:
1 - nROADS Fleet® LED Lightbar, built to your specifications
1 - Handheld Controller
Other Parts that May Be Included Depending on Your Configuration:
1 - Vehicle Specific Hook Kit w/ Hardware*
2 - Fixed Height Mounting Brackets w/ Hardware
1 - Flat Mount Hardware Kit or
2 - Headache Brackets w/ Hardware
*Kits will vary with each lightbar, depending on vehicle specified on order form.
Compatible Lights with This System (Ordered Separately):
2 or 4 - 4" mpower® Fascia Lights
Unpack Lightbar
1. Remove the lightbar from box and packaging.
2. Save packaging for later shipping.
3. Check components/ contents.
4. Please reference these instructions for proper wiring and installation.
• Warning devices are strictly regulated and governed by Federal,
State and Municipal ordinances. These devices shall be used
ONLY on approved vehicles. It is the sole responsibility of the
user of these devices to ensure compliance.
• DO NOT install this product or route any wires in the air bag
deployment zone. Refer to your vehicle owner’s manual for the
location of any air bag deployment zones.
• DO NOT connect this device to a strobe power supply. This
product is self-contained and does not require an external
power supply.
IMPORTANT NOTICE TO INSTALLER:
Make sure to read and understand all instructions
and warnings before proceeding with the installation of this product. Ensure that
the manual and any warning cards are delivered to the end user of this equipment.
Proper installation of the lightbar requires the installer to have a thorough knowledge of
automotive electronics, systems, and procedures. Lightbars provide an essential function
of an effective visual warning system. The use of the lightbar does not insure that all
drivers can or will abide by or react to an emergency warning signal, especially at high
rates of speeds or long distances. The operator of the vehicle must never take the right of
way for granted and it is the operator’s responsibility to proceed safely. The effectiveness
of the lightbar is highly dependant on the correct mounting and wiring. The installer must
read and follow the manufacturer’s installation instructions and warnings in the manual.
The vehicle operator should verify daily that the lightbar is securely fastened to the vehicle
and properly functioning before operating vehicle. The lightbar is intended for use by
authorized personnel only. It is the user’s responsibility to ensure they understand and
operate the emergency warning devices in compliance with the applicable city, state and
federal laws and regulations. SoundOff Signal assumes no liability for any loss resulting
from the use of this warning device.
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void
warranty coverage. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at
www.soundoffsignal.com/sales-
support. If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. or after hours 5 p.m. to 8 p.m. EST at 1.800.338.7337 (press
#4 to skip the automated message). Questions or comments that do not require immediate attention may be emailed to
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
A
A
B
B
C
C
D
D
E
E
F
F
G
G
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
CAD DIMENSIONS ARE BASIC
UNLESS OTHERWISE SPECIFIED
GD&T TO FOLLOW
ASME Y14.5M-1994
DRAWING NO:
B
PRIMARY DIMS:
INCH
DUAL DIMS: [mm]
TOLERANCES
EXCEPT AS NOTED
.X ± .020
.XX ± .012
.XXX ± .006
ANGLES ± .5°
DO NOT SCALE
DRAWING
SIZE:
SHEET
1 OF 3
DESCRIPTION:
REVISION:
®
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE
PROPERTY OF SOUNDOFF SIGNAL.
ANY REPRODUCTION IN PART OR
AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
SOUNDOFF SIGNAL IS PROHIBITED.
THIRD ANGLE
PROJECTION
MESA LIGHT BAR ASSEMBLY
MATERIAL:
MESA_LIGHT_BAR_ASSEMBLY-INSTALL.SHEET.UPDATES
1.800.338.7337 / www.soundoffsignal.com
For Quick Install Video please visit:
https://www.soundoffsignal.com/products/nroads-fleet-cng-lightbar/
