Sorvall TC6 Скачать руководство пользователя страница 83

Страница: 83 / 109

Repair and Replacement

SORVALL



Centrifuges

5-16

11. Remove the defective power connector. Then, remove the fuse

block and fuses from the defective power connector and install
into the new power connector assembly (PN 78028, SN 9600946,
60 Hz and above).

NOTE

SN 9501734 and above, 50 Hz instruments have filter
(PN 78038) mounted with two M4 pan head screws
(PN 91280) and two lockwashers (PN 63936).

12. Install the new power connector securing in place with the

hardware retained in step 9.

13. Reconnect P/J41 and the ground wire.

14. Reassemble the centrifuge reversing steps 1 through 8.

NOTE

When reinstalling the cabinet, be sure the slots of the
cabinet frame engage the flanges on the baseplate. If
necessary, use a rubber mallet to tap into place. Refer
to figure 5-5.

5-14. Speed Potentiometer

Replacement

NOTE

Retain all hardware for reassembly unless otherwise
advised.

1. Turn centrifuge power off and unplug power cord.

2. From the front bezel, use an Allen wrench to remove the set

screw from the

SPEED

knob. Remove knob.

3. Remove the nut and star washer.

4. Remove the two phillips screws located on each side of the

bezel. Carefully lift the bezel up to disengage it from the frame
(but do not disconnect).

5. From the back of the bezel, remove the speed potentiometer —

note the proper orientation of the wires to terminals, then cut
the wires.

6. Strip approximately .6 to 1.3 cm (1/4 to 1/2 inch) of the insula-

tion from the cut wires. Solder the wires from the harness to the
new potentiometer.

7. Install the potentiometer and secure it in place with the hardware

removed in step 3.

Содержание TC6














































































































Результаты поиска

Содержание TC6

Отзывы:

Похожие инструкции для TC6

Бренды по названию

Популярные бренды

Sorvall TC6, Руководство по обслуживанию

Результаты поиска

Содержание TC6

Отзывы:

Похожие инструкции для TC6

Бренды по названию

Популярные бренды