manualshive.com logo in svg

Sorvall TC6, Руководство по обслуживанию

Поделиться
Скачать
Sorvall TC6 Скачать руководство пользователя страница 18

TC6

®

Installation and Operation

2-3

POWER

CORD

SELECTED

VOLTAGE

WINDOW

TABS

POWER

CONNECTOR

POWER

CONNECTOR

FUSE

BLOCK

FUSE

BLOCK

VOLTAGE
SELECTOR

VOLTAGE
SELECTOR

VOLTAGE

WINDOW

SELECTABLE

VOLTAGES

FUSES

Figure 2-1.  Voltage Selection (SN 9501733 and below)

3. Gently pull the voltage selector from the fuse block.

4. Rotate the voltage selector until the desired voltage is aligned

with the window in the fuse block.  Then, reinstall the voltage
selector into the fuse block.

5. Check that proper fuses are installed.  Fuses are Type T, 250 V,

but change amperage rating depending on the voltage selected:

•

100 or 110 setting

 requires two 3.15-amp fuses, (PN 91428),

•

220 or 240 setting

 requires two 2-amp fuses, (PN 91203).

Change fuses if necessary.

6. Reinstall the fuse block into the power connector and plug in

the centrifuge power cord.

NOTE

If the voltage was changed from 100-110 setting to 220-
240 setting, a different power cord is required.

!

C A U T I O N

When changing the voltage

setting, be sure that the voltage
selector is installed so that the voltage
displayed in the voltage window
matches the intended input voltage.
Also, be sure that the proper fuses
have been installed, and that you are
using the proper power cord.
Incorrect installation can result in
damage to the centrifuge.  Sorvall is
not responsible for incorrect
installation.

Содержание TC6














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды