Sony KV-32XBR400, Руководство по обслуживанию

Страница: 41 / 126

—
41
—
K
V-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C
Control Register
Function & Link Data
Type
Data
Range
Comment
Full Vcomp1 Vcomp2
0 SBHS DC AMP3: DC shift Adj. 0~63 31 [31]
1 YBWU VCA9: Upper Y-bow Adj. 0~63 31 [31]
2
YBWL
VCA10: Lower Y-bow Adj. 0~63 31 [31]
3 RSAP DC AMP2: Right H-AMP Adj. 0~63 31 [31]
4 RUBW VCA5: Right upper bow Adj. 0~63 31 [31]
5
RLBW
VCA6: Right lower bow Adj. 0~63 31 [31]
6 LSAP DC AMP1: Left H-AMP Adj. 0~63 31 [31]
7 LUBW VCA1: Left upper bow Adj. 0~63 31 [31]
8
LLBW
VCA2: Left lower bow Adj. 0~63 31 [31]
9 CADJ DC AMP4: Offset adjustment (ADJ) Adj. 0~63
10 CPY2
Copy Function 2: (Set CPY2=1, then press MUTE + Enter.)
Copy all CXA8070 data for Full mode to Vcomp1&2 modes.
Micro
0, 1
For engineering design use only
DX1A SERVICE LIST (#6):
D-CONV / CXA8070
Device Name: CXA8070AP { DY-Convergence Control / SONY } / IC5513 (D-board) / P/N: 8-759-595-52 (SB#: V1718)
Slave Address: DEh
31 [31]
31 [31]
31 [31]
31 [31]
31 [31]
31 [31]
Full: 480p/960i (4x3) display mode
Vcomp1: 480p/960i (16x9) display mode
Vcomp2: 1080i (16x9) display mode
Adj.: Adjusted data
From the system micro (V 2.0),
the deflection control-related initial settings
are the same as their average data.
0
Note:
Data Initial Settings & [Average Data]
( 32V&36V CRTs)
Register
No & Name
48 [48]
31 [31]
31 [31]
31 [31]
Control Register
Function & Link Data
Type
Data
Range
Comment
Full Vcomp1 Vcomp2
0 DFON SW0: DF on/off switch C 0, 1 0
1 DQP PWM: DQP phase Adj. 0~63 23 [23] 23 [23]
2 DF DAC1: DF phase Adj. 0~63 25 [25] 25 [25]
3 DQPD H.AMP: DQP dc-level Adj. 0~63 34 [34] 34 [34]
4 QPDV U.CBOW, L.CBOW: DQP dc-level vertical modulation 0~63 51 47
5 DVS U.CBOW, L.CBOW: DQP dc-level tilt 0~(3)~7 0 0
6 QPDY U.MBH,L.MBH: DQP dc-level at top & bottom areas 0~63 7 7
( ): Settings at center
7 DQPA DC SHIFT: DQP amplitude Adj. 0~63
22 [27]
(32V)
or
13 [15]
(36V)
22 [27]
(32V)
or
13 [15]
(36V)
22 [27]
(32V)
or
13 [15]
(36V)
Data
(36V)
are used as Initial/CBA data.
From the system micro (V 2.0), most
deflection control-related initial settings
are the same as their average data.
8 QPAV U.YBOW, LYBOW: DQP amplitude vertical modulation 0~63 38 34
9 AVS U.YBOW, LYBOW: DQP amplitude tilt 0~7 3 3
10 NORM SW1: 0, 1 0 0
11 CPY3
Copy Function 3: (Set CPY3=1, then press MUTE + Enter.)
Copy all CXA8070 data for Full mode to Vcomp1&2 modes.
Micro 0, 1 0 For engineering design use only
12 200V H.DUTY, H.TILT: 200V regulator adjustment Adj. 0~63 31 [31]
Note:
Register
No & Name
Full: 480p/960i (4x3) display mode
Vcomp1: 480p/960i (16x9) display mode
Vcomp2: 1080i (16x9) display mode
C: Common data
Adj.: Adjusted data
U.CBOW = QPDV + DVS
L.CBOW = QPDV - DVS
U.YBOW = QPAV + AVS
L.YBOW = QPAV - AVS
DX1A SERVICE LIST (#7):
CXA2026AS
Device Name: CXA2026AS { DQP Control / SONY } / IC5511 (D-board) / P/N: 8-752-074-64 (SD#: S95610B)
Slave Address: 8Eh
Data Initial Settings & [Average Data]
(32V&36V CRTs)