SONIX SN8P2308 Скачать руководство пользователя страница 7

Страница: 7 / 119

SN8P2318 Series

C-type LCD, RFC 8-Bit Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 7

Version 1.5

PRODUCT OVERVIEW

1.1 FEATURES



Features Selection Table

CHIP

ROM

RAM

Stack

Timer

PWM

RFC

Ext.

Int

I/O

LCD Driver

Package

TC0

Dot

C-type

R-type

SN8P2308 4K*16

128*8

2-ch

4*32

LQFP64

SN8P2318 4K*16

128*8

5-ch

4*32

LQFP64

SN8P2317 4K*16

128*8

5-ch

4*21

LQFP48



Memory configuration



Fcpu (Instruction cycle)

ROM size: 4K * 16 bits.

Fcpu = Fosc/1, Fpsc/2, Fosc/4, Fosc/8, Fosc/16.

RAM size: 128 * 8 bits.



One 8-bit basic timer. (T0).



8 levels stack buffer.



One 8-bit timer/counter (TC0) with duty/cycle



5 interrupt sources

programmable PWM and IR carry signal.

3 internal interrupts: T0, TC0, T1



One 16-bit timer/counter (T1) with auto-reload/

2 external interrupt: INT0, INT1

counter/capture timer supports for RFC function.



5-Channel RFC (Resistor to Frequency Converter)



I/O pin configuration



4*32 LCD Driver (128 dots) supports internal C type

Bi-directional: P0, P1, P5.

and external R type bias.

Bi-directional and shared with SEG pins: P2, P3.



On chip watchdog timer and clock source is

Input only shared with reset pin: P0.3.

Internal low clock RC type (16KHz @3V, 32KHz

Wakeup: P0, P1 level change.

@5V).

Pull-up resisters: P0, P1, P2, P3, P5.

External interrupt pin:



4 system clocks

P0.0 trigger edge controlled by PEDGE.

External high clock: RC type up to 10 MHz

P0.1 level change trigger.

External high clock: Crystal type up to 16 MHz

Event counter input:

Internal high clock: PLL 16MHz from 32K X’tal.

TC0 event counter input pin: P0.0

Internal low clock: RC type 16KHz(3V), 32KHz(5V)

T1 event counter input pin: P0.2

RFC channel pins: P1.0~P1.4.



4 operating modes

Normal mode: Both high and low clock active



3-Level LVD: 2.0V/2.4V/3.6V

Slow mode: Low clock only.



Powerful instructions

Sleep mode: Both high and low clock stop

Instruction’s length is one word.

Green mode: Periodical wakeup by timer

Most of instructions are one cycle only.

All ROM area JMP/CALL instruction.



Package (Chip form support)

All ROM area lookup table function (MOVC).

LQFP 48 pin

LQFP 64 pin

Содержание SN8P2308
























































































































Результаты поиска

Содержание SN8P2308

Отзывы:

Похожие инструкции для SN8P2308

Бренды по названию

Популярные бренды

SONIX SN8P2308, Руководство пользователя

Результаты поиска

Содержание SN8P2308

Отзывы:

Похожие инструкции для SN8P2308

Бренды по названию

Популярные бренды