manualshive.com logo in svg

SONIX SN8P2308, Руководство пользователя


Поделиться
Скачать
background image

SN8P2318  Series 

C-type LCD, RFC 8-Bit Micro-Controller

 

SONiX TECHNOLOGY CO., LTD

                           

Page 36

                                                Version 1.5

 

 

2.5    CODE OPTION TABLE 

The code option is the system hardware configurations including oscillator type, watchdog timer operation, Noise Filter 
option, LVD option, reset pin option and OTP ROM security control. The code option items are as following table:   
 

Code Option 

Content 

Function Description 

High_Clk 

PLL_16M 

High  speed  internal  16MHz  PLL.  External  low-speed  32K  oscillator  free 
runs.  XOUT  pin  is  bi-direction  GPIO  mode.  XIN  pin  connects  a  0.1uF 
decouple capacitor to VDD. 

RC 

Low cost RC for external high clock oscillator. XIN pin is connected to RC 
oscillator. XOUT pin is Fcpu signal output. 

12M X’tal 

High  speed  crystal  /resonator  (e.g.  12MHz)  for  external  high  clock 
oscillator. 

4M X’tal 

Standard crystal /resonator (e.g. 4M) for external high clock oscillator. 

Low_Clk 

32K X’tal 

Low  frequency,  power  saving  crystal  (e.g.  32.768KHz)  for  external  low 
clock  oscillator.  LXIN/LXOUT  pins  drive  external  32768Hz  low  speed 
crystal/ceramic oscillator.   

RC 

LXIN pin drives external RC oscillator to GND. LXOUT pin outputs Flosc 
clock.   

Fcpu 

Fhosc/1 

Instruction cycle is 1 oscillator clocks. 

Fhosc/2 

Instruction cycle is 2 oscillator clocks. 

Fhosc/4 

Instruction cycle is 4 oscillator clocks. 

Fhosc/8 

Instruction cycle is 8 oscillator clocks. 

Fhosc/16 

Instruction cycle is 16 oscillator clocks. 

Watch_Dog 

Always_On 

Watchdog  timer  is  always  on  enable  even  in  power  down  and  green 
mode. 

Enable 

Enable  watchdog timer. Watchdog timer stops in  power down mode and 
green mode. 

Disable 

Disable Watchdog function. 

Reset_Pin 

Reset 

Enable External reset pin. 

P03 

Enable P0.3 input only without pull-up resister. 

Noise_Filter 

Enable 

Enable Noise_Filter. 

Disable 

Disable Noise_Filter. 

Security 

Enable 

Enable ROM code Security function. 

Disable 

Disable ROM code Security function. 

LVD 

LVD_L 

LVD will reset chip if VDD is below 2.0V 

LVD_M 

LVD will reset chip if VDD is below 2.0V 
Enable LVD24 bit of PFLAG register for 2.4V low voltage indicator. 

LVD_H 

LVD will reset chip if VDD is below 2.4V 
Enable LVD36 bit of PFLAG register for 3.6V low voltage indicator. 

LVD_MAX 

LVD will reset chip if VDD is below 3.6V 

 

2.5.1 High_Clk code option 

High_Clk code option control system high speed oscillator type in

cluding PLL_16M, RC, 4M X’tal and 12M X’tal. In 

PLL_16M mode, XIN connects 0.1uF decouple capacitor to VDD. XOUT is bi-direction GPIO mode. In RC mode, 
XOUT is Fcpu signal output. 
 

2.5.2 Low_Clk code option 

Low_Clk code option control system low speed oscillator type including 32K 

X’tal and RC. In RC mode, LXIN connects 

RC oscillator (LXIN connects capacitor to GND), and LXOUT pin outputs Flosc signal for measuring RC frequency.   
 

2.5.3 Fcpu code option 

Fcpu  means  instruction  cycle  of  normal  mode  (high  clock).  In  slow  mode,  the  system  clock  source  is  external  low 
speed 32KHz oscillator connected to LXIN/LXOUT pins. The Fcpu of slow mode isn

’t controlled by Fcpu code option 

and fixed Flosc/4.   

Содержание SN8P2308
























































































































Отзывы:

Нет отзывов

Похожие инструкции для SN8P2308

iCeeO2 C30 Instruction Manual preview
C30
Бренд: iCeeO2 Страницы: 7
Parker ACR7000 Series Hardware Manual preview
ACR7000 Series
Бренд: Parker Страницы: 21
Parker AC890PX Series Quick Start Manual preview
AC890PX Series
Бренд: Parker Страницы: 26
Vageo DT-1 Manual preview
DT-1
Бренд: Vageo Страницы: 2
Watts KONTACT Manual preview
KONTACT
Бренд: Watts Страницы: 17
Securi-Prod LK190 Installation Manual preview
LK190
Бренд: Securi-Prod Страницы: 3
Grosvenor Janus C4 485 Installation Manual preview
Janus C4 485
Бренд: Grosvenor Страницы: 5
Watlow EZ-ZONE PM L AAAAB Series User Manual preview
EZ-ZONE PM L AAAAB Series
Бренд: Watlow Страницы: 30
Quicksmart EtherRain User Manual preview
EtherRain
Бренд: Quicksmart Страницы: 10
Aerotech Ensemble HLe Hardware Manual preview
Ensemble HLe
Бренд: Aerotech Страницы: 112
Advanced Control Technologies th104 Installation Instructions preview
th104
Бренд: Advanced Control Technologies Страницы: 3
Magnetek IMPULSE G+ Series 3 Instruction Manual preview
IMPULSE G+ Series 3
Бренд: Magnetek Страницы: 9
Carrier WSHP Open v3 Integration Manual preview
WSHP Open v3
Бренд: Carrier Страницы: 58
Full Gauge Controls MT-514e Manual preview
MT-514e
Бренд: Full Gauge Controls Страницы: 5
V2 PESO-230V Manual preview
PESO-230V
Бренд: V2 Страницы: 108
Datapath iolite 600 Quick Start Manual preview
iolite 600
Бренд: Datapath Страницы: 16
Geco GH10HA User Manual preview
GH10HA
Бренд: Geco Страницы: 20
CKD ABSODEX MINI AX6000M Series Manual preview
ABSODEX MINI AX6000M Series
Бренд: CKD Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды