12
Before using the product for the first time, please read the instructions for use below and retain them for later reference. The original instructions were written in the Hungarian language.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised at all times to ensure that they do not play with the appliance.
After unpacking, please, check the device for possible transport damages. Keep the packaging away from children, if it contains bags or other potentially dangerous components.
ReSettING tHe UNIt
The microprocessor data requires resetting in situations where the power supply is lost or the unit (including its display) acts erratically. In order to do so, press the
RSt (ReSet)
button below the rotating knob using
a sharp object. This will clear all stored data and return the unit to factory default condition. This operation is required after installation, before switching on the unit for the first time, and when the vehicle’s battery
is replaced.
SetUP & SwItCHING ON / OFF
Press the
button to power the unit on. The unit will switch to RADIO mode after being switched on for the first time.
• Later on, it will automatically switch to the most recently used function after being switched on unless the external storage device has been removed in the meantime.
• Since voltage surges can occur when the vehicle’s engine is started, only turn on the unit after the engine has been started. Turn off the unit before stopping the engine. To turn off the unit, press the
button.
aDjUStING vOLUme
Use the
rotating knob
to set the desired volume level.
• If the unit is in any particular setting mode, you will need to exit the mode first.
• The volume can be adjusted in a range of 00 to 40.
BaSIC SettINGS & SeLeCtING tHe DeSIReD LaNGUaGe
Press the
meNU
button then use the
rotating knob
to select the lowest
SettING
function then press the
rotating knob
. The Setup menu appears. The following parameters can be adjusted: menu language, date,
12/24-hour time format, current time, repeat, factory settings.
The desired function can be selected using the rotating knob, which can then be modified by pressing the rotating knob.
Language:
With the top row selected, repeatedly press the rotating knob until the desired language is displayed
(GB / HU / SK / RO / SRB / SLO)
Date:
Selecting the second row, press the rotating knob then rotate it to set the year. Pressing it again will allow you to set the month then pressing it again will allow you to set the day.
Clock mode:
Selecting the third row, press the rotating knob to select 12-hour (AM/PM – morning/afternoon) or 24-hour display mode for the clock.
Current time:
The fourth row can be used to set the clock just like the date.
Repeat:
Setting for playback of tracks on connected external storage (USB/SD): Repeat off / Repeat current track / Repeat all tracks.
Factory default:
By selecting this row and pressing the rotating knob will reset the unit to the factory defaults.
After completing the settings, press the
meNU
button. The menu will appear in the desired language then after a brief moment shift to
RaDIO
mode.
• The CH- / CH+ buttons can be used instead of the rotating knob for adjusting the settings.
SeLeCtION OF SIGNaL SOURCe
The source to be listened to or viewed can be selected in two ways:
A., Press one of the following buttons:
RaDIO / mUSIC / PHOtO / mOvIe
B., It can also be selected using the menu by pressing the
meNU
button and the
rotating knob
.
• The given signal source cannot be activated unless it is available. For example, if no storage device is connected on which the appropriate files can be found (songs, photos or films).
• Press the MENU button repeatedly to go higher in the directory hierarchy. Any directory can be selected by turning the rotating knob then pressing it.
• On switching on the unit, the previously played track will continue playing unless the device containing it has been removed.
• If there are external devices connected to both the USB and SD sockets, the MUSIC button can be used to select between them. The use of SD cards is preferred on account of their secure and protected location on the unit.
• After connecting, the external unit connected last will be the one that will start playing.
• A check mark appears in front of the symbol corresponding to the selected signal source after USB or SD devices are inserted.
aUDIO SettINGS & eQ
Repeatedly and briefly press the
tONe
button to select the parameter to be adjusted:
vOL / BaS / tRe / BaL / FaD / eQ / LOUD.
Adjustment is possible using the rotating knob.
• Unless an adjustment is made within 4 seconds, the unit will automatically revert to the previous function.
• By default, the rotating knob will adjust the volume.
• The window that appears when adjusting audio settings will show the length of the current track and the elapsed time.
• When listening at high volume, do not set the bass and treble too high, as this may lead to distortion! The recommended setting is FLAT..
vOLUme
volume adjustment (00 – 40)
BaSS
bass level adjustment (-7…0…+7)
tReBLe
treble level adjustment (-7…0…+7)
BaLaNCe
left and right channel balance (L7…0…R7)
FaDeR
front and rear channel volume fader (R7…0…F7)
eQUaLIZatION
EQ settings (FLAT / CLASSIC / ROCK / POP)
LOUDNeSS
loudness control (LOUD OFF / LOUD ON)
LOUDNeSS
Human hearing is less sensitive to low and high frequency sound at low volumes. By turning on the
LOUD
function, the automatic EQ compensates for this phenomenon at lower volumes. It is recommended to be
turned off at higher volumes because it can cause the sound to be distorted.
• For the benefit of better sound quality, before using this function, we recommend selecting the setting EQ FLAT and setting the bass and treble controls to “0.”
• The higher the volume, the less effect will automatic loudness correction will have on the sound.
USING tHe RaDIO
After the unit is switched on the radio will turn on if it was being previously listened to – or the USB/SD signal source last played has been removed.
If necessary, use the
RaDIO
button to select the radio function. The FM1-FM2-FM3 and AM1-AM2 bands are accessible by pressing it repeatedly.
maNUaL tUNING & StORING StatIONS
Using the
RaDIO
button, select the
Fm1
band. You can verify this at the top row of the display. Select the first row using buttons
CH-/CH+
(Program position 1) then press the rotating knob for confirmation. Briefly
keep pressing the
9
:
buttons to manually tune in the desired radio station. Keep the same buttons pressed for automatic search (TA SEEK indication). The tuning will stop at the next radio station. Any stations
found can be stored under the first preset by pressing the
rotating knob
. If the radio station has RDS service and the
PtY
function is active on the unit, the display will alternately show the broadcast frequency, the
name of the radio station and the program type (e.g., POP MUSIC). To store a new radio station under the second preset, press the CH+ button then, after selecting the second row, press the
rotating knob
. Then
search for the program to be stored here as described above then save it by pressing the rotating knob and proceed to the third preset.
• A total of 18 FM and 12 AM radio stations can be stored. By repeatedly pressing the RADIO button select an option from among FM1-FM2-FM3 or AM1-AM2. Six stations can be stored for each band. If for example preset (row)
4 is selected in band FM2, then band FM2 will need to be selected first (RADIO) and then row 4 selected. Be sure to press the rotating knob after selection. Only then will the saved preset be able to be listened to.
• If a given preset is in use, its content will be erased and a new station frequency stored in its place.
• Whenever a station with good reception is being received, the indicator ST (stereo) will illuminate on the display.
• If the unit is being used at a distance from the original tuned location – such as when travelling – the same station might have to be tuned in again on a different frequency. The same program is broadcast on different
frequencies in different geographical locations! This inconvenience can be avoided if the station being listened to features RDS and you activate the AF (Alternate frequency) feature on your unit.
aUtOmatIC tUNING aND StORING
Keep the
RaDIO
button pressed for 2 seconds to automatically search for and store the radio stations available in the current area. Tuning and storage progress can be monitored on the display. Each receivable
frequency is checked. The better the conditions for reception, the more stations will be found.
• Please remember that the unit may skip stations with weaker reception, and the stations may be stored in a sequence different from what you have defined.
• Select manual tuning and preset storage in order to perform custom settings.
Figure 4
USB/SD/SDHC/mmC
USB & SD/SDHC/MMC memory card slot
