background image

Copyright © 2010 Somfy SAS. All rights reserved.

Pergola sc io

39

EN

3.3. Motor/tube assembly

Slide the motor into the roller tube. 

1) 

For smooth roller tubes, position the notch previously cut 
on the crown.
For safety reasons, fix the roller tube to the drive wheel 

2) 

with 4 x Ø 5 mm self-tapping screws or 4 x Ø 4.8 mm 
steel pop rivets located:

at least 5 mm from the outer rim of the drive wheel: 

 

-
L1 - 5, and

no more than 15 mm from the outer rim of the drive 

 

-
wheel: L1 - 15.

The screws or pop rivets must only be attached to the drive wheel and not to the motor.

3.4. Installing the tube/motor assembly

Fit the tube/motor assembly to the end bracket (C).

1) 

Fit the tube/motor assembly to the motor bracket (D).

2) 

Depending on the type of bracket, position the retaining ring 

3) 

(E) (for motors 

 85 Nm with a retaining ring, it is essential 

to use the locking retaining ring (F)).

15 mm

5 mm

20 mm

L1

1

2

C

D

E

F

1

2

3

Always make a loop in the power supply cable to prevent 

water entering the motor!

Cut off the mains power supply.

 

-

Connect the motor according to the information in the 

 

-

table below:

230 V ~ 50 Hz

Motor cable

1

Brown

Live (P)

2

Blue

Neutral (N)

3

Yellow/Green

Earth ( )

1

2

3

1

2

3

OFF

230 V

~

50 Hz

3 x 1.5 mm

2

3 x 0.75 mm

2

4. WIRING

Markizy.by

Содержание Pergola sc io













Отзывы: