Elixo 800/1300/2000
Copyright © 2011 Somfy SAS. All rights reserved.
11
EN
6.1. storing the remote controls
To memorise the remote controls, use the PROG button of the
RTS radio module.
6. QuiCk CommissioNiNG
[1]
[2]
.......2 min........
PROG
2 s
PROG
PROG
PROG
PROG
10
9
11
13
12
14
15
16
17
18
19
20
21
22
DL10
DL11
ENC
ODER
DL12
PAUSA LAVORO PROG
SW
1
SW
2
1
2
3
4
5
6
7
8
VO
YA
NT
e
2
C
SOG
MODULE RADIO RT
S
/4A
F1
F2
O
N
O
N
PROG
21
22
DL10
DL11
EN
C
O
D
ER
DL12
PAUSA LAVOR
AA
O PROG
SW
1
SW
2
2
VO
YAYY
N
T
e
2
C
SO
G
M
O
DULE RADI
O
RT
S
/4
A
F1
F2
O
N
O
N
1
3
4
5
6
7
8
9
10
11
14
12
13
15
16
17
20
18
19
PROG
START
PED
STOP
FOTO
FCA
FCC
COSTA
+
-
RE
G
+
-
RE
G
LAVORO PROG
PAUSA
10
9
18
19
20
21
22
START
PED
STOP
FOTO
FCA
FCC
COSTA
DL10
DL11
ENCODER
DL12
SW1
SW2
1
2
3
4
5
6
7
8
SOG/4
A
F1
F2
O
N
O
N
+
-
R
EG
LAVOR
AA
O PROG
PAUSA
21
22
START
PED
STOP
FOTO
FCA
FCC
COSTA
DL10
DL11
EN
C
O
D
ER
DL12
SW
1
SW
2
2
SO
G
/4
A
F1
F2
O
N
O
N
1
3
4
5
8
6
7
9
10
19
20
18
PROG
6.1.1. memorising a 2 or 4 button remote control
[1].
Press the PROG button of the RTS radio module
(approximately 2 s) until the red indicator lights up
continuously.
[2].
Press the radio control channel to be assigned to the
motor within 2 min. The red indicator will flash, the remote
control is memorised.
If this procedure is carried out using a channel which has
already been memorised, this channel will be cleared.
6.1.2. Exit the programming mode without programming a remote control
Press the PROG button of the control unit briefly.
6.2. Programming the impact force and the slowing zones
This programming step makes it possible to:
- set the impact force of the gate, in case of an impact with an obstacle in the slowing phase,
-
define the start point for slowing of the gate when opening and closing.
The slowing point can be excluded.
6.2.1. Before programming
•
If the electrical and safety devices (photoelectric cells, orange
light, etc.) must be installed, they must be connected before
programming (see connecting peripherals page 13).
Check that they operate correctly:
- The NC input LED indicators (stop, photoelectric cells,
end limit, safety edge) must be lit.
- The NO input LED indicators (open/close, pedestrian
open) must be off.
In case of a fault, identify the problem and resolve it.
•
The REG potentiometer must be positioned b and -.
•
The gate must be opened approximately 50 cm.
