Solplanet ASW S Series Скачать руководство пользователя страница 54

 

UM0012_ASW 5-10k Series_EN_V03_0522                                                                            53 

 

Clean the heat sink with compressed air or a soft brush. Do not use 

aggressive chemicals, cleaning solvents or strong detergents.   

For proper function and long service life, ensure free air circulation around the 

heat sink. 

 

13 Recycling and disposal 

Dispose of the packaging and replaced parts according to the 

rules applicable in the country where the device is installed. 

Do not dispose the ASW inverter with normal domestic waste. 

 

 

 

14 EU Declaration of Conformity 

within the scope of the EU directives 

• Electromagnetic compatibility 2014/30/EU (L 96/79-106, March 29, 

2014) (EMC). 

• Low Voltage Directive 2014/35/EU (L 96/357-374, March 29, 2014)(LVD). 

• Radio Equipment Directive 2014/53/EU (L 153/62-106. May 22. 2014) (RED) 

AISWEI Technology (Shanghai) Co., Ltd. confirms herewith that the inverters 

described in this manual are in compliance with the fundamental requirements 

and other relevant provisions of the above mentioned directives.   

The entire EU Declaration of Conformity can be found at 

www.solplanet.net

 

 

 

 

 

 

Do not dispose of the product together with the household waste but in 

accordance with the disposal regulations for electronic waste applicable at 

the installation site. 

Содержание ASW S Series


























































Отзывы: