Solid State Cooling Systems THERMOCUBE 200 Скачать руководство пользователя | Manualshive

Страница: 25 / 40

background image

T

HERMO

C

UBE

200/300/400

T

HERMOELECTRIC

C

HILLER

M

ANUAL

52-11300-1

S

OLID

S

TATE

C

OOLING

S

YSTEMS

,

167

M

YERS

C

ORNERS

R

OAD

,

W

APPINGERS

F

ALLS

,

NY

12590

24

T

ELEPHONE

:

(845)

296-1300

F

AX

:

(845)

296-1303

WEB

:

WWW

.

SSCOOLING

.

COM

V

ERSION

M28

-EF: External Filter Option

This option adds an external 5 micron filter to the ThermoCube
coolant outlet for systems sensitive to particulate matter in the
coolant. Note that this option also dampens coolant flow pulses,
producing a smoother coolant flow.

-FL: Fluorinert or Galden

This option  is selected to configure the ThermoCube for
perfluorinated  or hydro fluorinated  ether processs fluids such as
Fluorinert or Galden.  CAUTION: Make sure this option is included
in  your ThermoCube configuration if you plan to use these process
fluids.

-HT: High Temperature Operation Option

The ThermoCube normally has a 55 °C thermostat on its liquid cold
plate that shuts off heating to protect against hot coolant damaging
the operator’s equipment. The –HT option replaces this thermostat
with a 70 °C thermostat and adds insulation to allow operation up
coolant temperatures of 65 °C. Note: The Maximum specified
temperature for standard Centrifugal pumps (-1C and -1CL) is 60 °C.

-LT: Low Temperature Operation Option

The ThermoCube normally has a 5°C thermostat on its liquid cold
plate that shuts off cooling to prevent freeze damage when using
water as a coolant. The –LT option removes this thermostat and
adds insulation to allow operation below the freezing point of water
(0°C). Select this option if you plan to regularly run at setpoints
below 8-10°C. When selecting this option, the operator must ensure
coolants are selected that will not freeze within 5°C of set point.
Repairs to thermoelectric heat exchangers damaged by freezing
water in Thermocubes with this option selected will not be covered
by warranty.

-PT: Preset Control Temperature

With this option the ThermoCube is shipped from the factory with a
preset control temperature specified by the customer, and manual
entry is disabled. The ThermoCube will always control to the preset
temperature and the user no longer has the ability to modify the
settings of the unit.

CAUTION

«
...
23
24
25
26
27
...
»

Содержание THERMOCUBE 200









































Отзывы:

Нет отзывов

Похожие инструкции для THERMOCUBE 200

Chill-O-Matic IN1500BKB

Бренд: B&D Страницы: 2

RowCool HCH1CD0

Бренд: Delta Страницы: 60

Бренд: Yard Machines Страницы: 20

630B-Tuffy, 634F-Bronco, 634B-

Бренд: Troy-Bilt Страницы: 32

Бренд: Neuton Страницы: 8

Бренд: CLIMAVENETA Страницы: 6

Бренд: ATC Страницы: 21

Бренд: EarthWise Страницы: 30

Бренд: Stiga Страницы: 14

Бренд: UNIA Страницы: 34

Бренд: VALERA Страницы: 2

Бренд: Daikin Страницы: 112

Бренд: Daewoo Страницы: 15

Бренд: Garland Страницы: 180

Бренд: Sammic Страницы: 84

Lancer P400T V2

Бренд: Hoshizaki Страницы: 17

Бренд: Jensen Страницы: 102

COOL CABI OCA-H1000BC-AW2

Бренд: OHM ELECTRIC Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды