Solera 434729 Скачать руководство пользователя

Страница: 12 / 12

lci1.com

574-537-8900

Rev:07.19.18

Solera

Power Awning 18V

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0001260

Maintenance - Solera Awnings

Fabric Care

If the awning is retracted while wet, extend the awning

and let it dry as soon as conditions allow before again

retracting. This will help prevent the formation of mildew

and add to the life of the awning.

NOTE:

Mildew does not form on the fabric itself, but on the

accumulated dust, dirt and grime.
Periodically clean vinyl or woven acrylic fabric using a

mixture of

1/4

cup of dish soap and five gallons of warm

water.

Liberally apply the mixture on the top of the fabric and

retract the awning for five minutes. This will apply the

mixture to the bottom of the fabric as well.

Extend the awning and hose off with fresh water.

Repeat if necessary.

Allow to dry before retracting.

Notes

Manual information may be distributed as a complete

document only, unless Lippert Components provides

explicit consent to distribute individual parts.
All manual information is subject to change without

notice. Revised editions will be available for free

download at

lci1.com

. Manual information is considered

factual until made obsolete by a revised version.
Please recycle all obsolete materials and contact

Lippert Components with concerns or questions.

Содержание 434729













Результаты поиска

Содержание 434729

Отзывы:

Похожие инструкции для 434729

Бренды по названию

Популярные бренды

Solera 434729, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 434729

Отзывы:

Похожие инструкции для 434729

Бренды по названию

Популярные бренды