solarwatt MyReserve 500 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 60

background image

Subject to changes | © 2017 SOLARWATT GmbH | AZ-TM-PME-0767 | Rev 008 | Version: 01/2017

Page 21

Konfi guration EnergyManager

Geräteinstallation

Vorbereitung und Planung

EN

5.5

Connecting the cables and lines

IMPORTANT

Commissioning of the MyReserve may only be car-

ried out by a qualifi ed electrician! There is a risk
of electric shock! When light is collected via the

PV array, the PV system delivers DC voltage to the
MyReserve and the power converter. Ensure that

you have disconnected the PV system!

5.5.1.

MyReserve 500

Connect the DC connection cables of the PV system, the
PV inverter, the voltage supply and the communication
cable to the MyReserve (see chapter 3.7 and 3.8 Layout
of the ACS) of the ACS. Use the appropriate wire end slee-
ves for this purpose. Observe the polarity of the DC cable.
Only clamp cables to free and marked terminal connec-

tions (see fi gure).

Secure the supply line for the voltage supply of the My-
Reserve separately with a maximum amperage of 6 A. All
protective conductors connected must have a minimum
cross-section of 1.5 mm².

Then fi t the cover back on the terminal strip. In doing so,

make sure that the ground cable for the battery module
remains accessible behind the cover.

Possible PV inverter model connection cross-section: 4 - 6 mm²
Poss. AC connection cross-section: 1.5 – 2.5 mm²
Poss. com. connection cross-section ACS: 0.5 – 1.5 mm²

•

from the cable

NOTE

Before connection, remove 12 mm of insulation

from the cable ends and fi t the wire end ferrules.

NOTE

NOTE

NOTE

«
...
19
20
21
22
23
...
»

Содержание MyReserve 500





























































Отзывы:

Нет отзывов

Похожие инструкции для MyReserve 500

G-DRIVE mobile USB

Бренд: G-Technology Страницы: 13

DSN-3200 - xStack Storage Area Network Array Hard...

Бренд: D-Link Страницы: 7

Бренд: Megatank Страницы: 12

Бренд: Badger Basket Страницы: 6

Бренд: ABSCO SHEDS Страницы: 23

Бренд: Seagate Страницы: 42

Бренд: AIC Страницы: 64

Бренд: Air innovations Страницы: 30

Feronia 00108066

Бренд: Hama Страницы: 8

Бренд: U-Line Страницы: 6

220-420LTO - QUICK

Бренд: TANDBERG Страницы: 8

Бренд: Hitachi Страницы: 58

Бренд: Hitachi Страницы: 192

Dv4 1140go - Pavilion Entertainment - Core 2 Duo GHz

Бренд: HP Страницы: 40

Бренд: HP Страницы: 48

Бренд: HP Страницы: 11

Compaq Presario,Presario 2128

Бренд: HP Страницы: 24

Compaq Presario,Presario 2100

Бренд: HP Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды