solarwatt MyReserve 500 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 60

solarwatt MyReserve 500 Скачать руководство пользователя страница 15

Subject to changes | © 2017 SOLARWATT GmbH | AZ-TM-PME-0767 | Rev 008 | Version: 01/2017

Page 15

Konfi guration EnergyManager

Geräteinstallation

Vorbereitung und Planung

EN

5

Installation

5.1

Requirements for the installation location

•

MyReserve must only be installed in dry indoor rooms
or outdoor areas that are protected from spray water.

X

•

Max. relative air humidity: 85%. Do not expose My-

Reserve to environments with higher humidity levels.

•

Optimal ambient temperature range: 0°C to 30°C;
max. permitted ambient temperature: 45°C.

•

Keep the product out of direct sunlight.

•

For the 4.4 kWh design, the wall and the mounting
material must have a static load-bearing capacity of
at least 80 kg.

•

MyReserve must not block access to disconnection
mechanisms at the setup location.

•

For maximum safety, install DC-side lightning and
overvoltage protection between MyReserve and the
PV plant.

•

Keep the product out of reach of children, mentally
handicapped persons, and animals.

•

Install the product in a location where it will not be at

risk of exposure to fl ooding. This is to be ensured by
installing the product at a suffi cient height (at least

20 cm), and in a location protected against water in-

or outfl ow.

•

Do not store fl ammable or explosive materials in the

installation room.

•

Do not install the product in heating rooms (defi ned

as solid-fuel heating systems with total nominal heat
output of over 50kW that cannot be used in other ca-
pacities), oil or wood storage depots, barns, sheds, etc.

NOTE

MyReserve does not operate at temperatures below -15°C or above +45°C. Unrestricted performance is pro-
vided for the household in the temperature range of 0°C to 30°C. Accelerated aging of the cells should be
taken into account at temperatures above +45°C.

NOTE

NOTE

NOTE

NOTE

Make sure that the wall which the MyReserve is to be installed on can support its weight (80 kg) and ensure
that suitable load-bearing fastening material is used.

NOTE

NOTE

NOTE

«
...
13
14
15
16
17
...
»

Содержание MyReserve 500





























































Отзывы:

Нет отзывов