SOLARFOCUS maximus L 150, Руководство по установке

Страница: 5 / 52

3 Technical requirements
–
In fulfilling the warranty/guarantee services, we
shall cover only the assembly time and the mate-
rials used, but not any travel or accommodation
costs necessary for the fitters/engineers or any
return transport costs.
–
SOLARFOCUS GmbH assumes no liability for
any consequential costs of damages.
–
The repair and/or warranty replacement shall be
carried out on site or in the SOLARFOCUS fac-
tory at our discretion.
–
The company SOLARFOCUSwill determine whe-
ther such work requires a repair or whether the
parts are to be replaced free of charge.
3.1.3 Claims rendered void
The warranty and guarantee claims are rendered
void if one of the following points applies:
–
Non-compliance with the technical requirements
> 4
–
Damage during transport.
–
Wilful damage.
–
Damage due to force majeure (water, fire, etc.).
–
Non-observance of information in the planning,
installation and operation manual.
–
Insufficient energy or water, fault in the hydrau-
lics.
–
Incorrect operation, failure to perform main-
tenance and cleaning as prescribed.
–
Commissioning and maintenance carried out by
non-certified companies.
–
Undocumented commissioning (no com-
missioning log) and/or maintenance (main-
tenance log).
–
It is almost impossible to produce flawless pain-
ted parts; for this reason, slight defects that do not
adversely affect proper use shall not be deemed
as grounds for complaint.
–
No claims can be accepted under the warranty if
unauthorised intervention (or action that has not
been explicitly approved by us the manufacturer)
has been carried out. In addition, the goods must
be paid for within the specified payment time-
frame.
3.1.4 Limitation of liability
SOLARFOCUS GmbH accepts no liability for injury or
material damage resulting from:
–
Failure to observe the instructions in this manual.
–
Use of the product for any purpose other than for
its intended use.
–
Employment of unqualified personnel.
–
Use of non-approved spare parts.
–
Technical modification of the product by the sys-
tem operator.
3.2 Standards, guidelines, regulations
The following bodies of regulations must be con-
sidered and adhered to during planning, installation
and operation of the heating system:
Standards for heating systems
–
EN 303-5 - Part 5: Heating boilers for solid fuels,
manually and automatically stoked, nominal heat
output of up to 500 kW
–
EN 12828 - Heating systems in buildings - Design
for water-based heating systems
–
EN 13384-1 - Chimneys - Thermal and fluid dyna-
mic calculation methods - Part 1: Chimneys ser-
ving one combustion appliance
–
ÖNORM H 5151 - Planning of central hot water
heating systems with or without hot water pre-
paration - Part 1: Building with a specific trans-
mission conductance value above 0.5 W/(K.m²)
–
ÖNORM 7510-1 - Checking of heating systems -
Part 1: General requirements and inspection -
national supplement to ÖNORM EN 15378
–
ÖNORM 7510-4 - Checking of heating systems,
Part 4: Simple testing of combustion systems for
solid fuels
Standards for structural setup and safety devi-
ces
–
TRVB 118 H - Technical guidelines for pre-
ventative fire protection (Austria)
–
ÖNORM H 5170 - Heating systems - requi-
rements for construction and safety technology as
well as for fire prevention and environmental pro-
tection
–
ÖNORM M 7137 - Compressed wood in natural
state - Wood pellets - Requirements for storage of
pellets at the ultimate consumer
Standards for fuel
–
EN ISO 17225-2 - Solid biofuels - Fuel spe-
cifications and classes; Part 2: Graded wood pel-
lets
–
1. BImSchV - Federal Immission Control
Ordinance - ordinance on small and medium
solid-fuel combustion systems (Germany)
Standards for heating water
–
ÖNORM H 5195-1 - Heat transfer media for buil-
ding services systems, Part 1: Preventing
damage from corrosion and scale formation in clo-
sed hot water heating systems (Austria)
–
VDI 2035 - Prevention of damage in hot water
heating systems (Germany)
–
SWKI BT 102-01 - Water quality for building sys-
tems (Switzerland)
–
UNI 8065 (Italy)
Installation manual maximus L 5