Sofarsolar SOFAR 1100TL Скачать руководство пользователя страница 75

Страница: 75 / 82

TROUBLESHOOTING HANDLING

SOFAR 1100...3300TL-G3

Name

Description

Solution

ConsistentFa

ult_DCI

The sample value of the

DCI between the master

DSP and the slave DSP is

not consistent

ConsistentFa

ult_GFCI

The sample value of the

GFCI between the master

DSP and the slave DSP is

not consistent

SpiCommLos

The SPI communication

between the master DSP

and the slave DSP is faulty

SciCommLos

The SCI communication

between the control board

and communications

board is faulty

RelayTestFail Grid relay error

PvIsoFault

The insulation resistance

is too low

Check the insulation resistance

between the PV generator and

earth (ground), and rectify the error

in the event of short-circuiting.

OverTempFa

ult_Inv

The temperature of the

inverter is too high

Ensure that the mounting position

and method both comply with the

necessary requirements.

Check whether the ambient

temperature at the installation

location exceeds the upper limit

value. If so, improve the ventilation

in order to reduce the temperature.

OverTempFa

ult_Boost

The DC/DC booster

temperature is too high

OverTempFa

ult_Env

The ambient temperature

is too high

Содержание SOFAR 1100TL



















































































Результаты поиска

Содержание SOFAR 1100TL

Отзывы:

Похожие инструкции для SOFAR 1100TL

Бренды по названию

Популярные бренды

Sofarsolar SOFAR 1100TL, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SOFAR 1100TL

Отзывы:

Похожие инструкции для SOFAR 1100TL

Бренды по названию

Популярные бренды