Sofarsolar SOFAR 1100TL Скачать руководство пользователя страница 74

Страница: 74 / 82

TROUBLESHOOTING HANDLING

SOFAR 1100...3300TL-G3

Name

Description

Solution

DciOCP

The DC current is too high Check the setting of the MPPT

input mode (parallel

mode/independent mode) of the

inverter and correct if required.

SwOCPInstan The grid current is too

high

Internal inverter error, switch the

DC switch OFF, wait 5 minutes and

then switch the DC switch ON.

Check whether the error has been

rectified. If not, please contact the

technical support department.

SwBOCPInst

ant

The input current is too

high

Check whether the input current is

higher than the maximum

permissible input current of the

inverter, then check the input

cables. If both are correct, please

contact the technical support

department.

Overload

Reflux overload timeout

Check whether the power is

outside the permissible range. If so,

set the power to the correct range.

ConsistentFa

ult_VGrid

The sample value of the

grid voltage between the

master DSP and the slave

DSP is not consistent.

ID49-ID55 are internal errors of the

inverter. Switch the DC switch OFF,

wait 5 minutes and then switch the

DC switch ON. Check whether the

error has been rectified. If not,

please contact the technical

support department.

ConsistentFa

ult_FGrid

The sample value of the

grid frequency between

the master DSP and the

slave DSP is not

consistent

Содержание SOFAR 1100TL



















































































Результаты поиска

Содержание SOFAR 1100TL

Отзывы:

Похожие инструкции для SOFAR 1100TL

Бренды по названию

Популярные бренды

Sofarsolar SOFAR 1100TL, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SOFAR 1100TL

Отзывы:

Похожие инструкции для SOFAR 1100TL

Бренды по названию

Популярные бренды