Sofarsolar HYD 3000-EP страница 60 Скачать руководство пользователя

Страница: 60 / 71

HYD 3K~6K-EP

User manual

。

- 55 -

inverter. Check whether the problem is

solved.

If no, please contact technical support.

Fault

EEPROM error

ID150

FlashFault

Communication board

FLASH error

ID153

SciCommLose(D

SCI

communication

error (DC)

ID154

SciCommLose(A

SCI

communication

error (AC)

ID155

SciCommLose(F

use)

SCI

communication

error (Fuse)

ID156

SoftVerError

Inconsistent

software

versions

Contact for technical support and software

upgrades.

ID157

BMSCommunica

tonFault

Communication failure

of lithium battery

Make sure your battery is compatible with

the inverter.

CAN communication is recommended.

Check the communication line or port of the

battery and inverter for faults.

ID161

ForceShutdown

Force shutdown

The inverter is performed a forced

shutdown

ID162

RemoteShutdown

Remote shutdown

The inverter is performed a remote

shutdown.

ID163

Drms0Shutdown

Drms0 shutdown

The inverter is performed with a Drms0

shutdown.

ID165

RemoteDerating

Remote derating

The inverter is performed for remote load

reduction.

ID166

LogicInterfaceDe

rating

Logic interface derating

The inverter is loaded by the execution

logic interface.

ID167

AlarmAntiReflux

ing

Anti reflux derating

The inverter is implemented to prevent

countercurrent load drop.

ID177

BMS OVP

BMS

over-voltage

alarm

Internal failure of lithium battery, close

inverter and lithium battery, and wait 5

minutes to open inverter and lithium battery.

Check that the problem is resolved. If not,

please contact technical support.

ID178

BMS UVP

BMS under-voltage

alarm

ID179

BMS OTP

BMS high temperature

warning

ID180

BMS UTP

BMS low temperature

alarm

ID181

BMS OCP

Warning of overload in

charge and discharge of

BMS

ID182

BMS Short

BMS short circuit alarm

Maintenance

Inverters generally do not need any daily or routine maintenance. Heat sink

should not be blocked by dust, dirt or any other items. Before the cleaning, make
sure that the DC SWITCH is turned OFF and the circuit breaker between inverter
and electrical grid is turned OFF. Wait at least for 5 minutes before the Cleaning.



Inverter cleaning

Please clean the inverter with an air blower, a dry & soft cloth or a soft bristle

Содержание HYD 3000-EP








































































Результаты поиска

Содержание HYD 3000-EP

Отзывы:

Похожие инструкции для HYD 3000-EP

Бренды по названию

Популярные бренды

Sofarsolar HYD 3000-EP, Руководство пользователя

Результаты поиска

Содержание HYD 3000-EP

Отзывы:

Похожие инструкции для HYD 3000-EP

Бренды по названию

Популярные бренды