Snorkel S3215E Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 90

Snorkel S3215E Скачать руководство пользователя страница 68

Chapter 11 – Emergency Operation

60

S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834

Valves with Brake Release Valve on Side of Valve

1. Chock the wheels to prevent uncontrolled motion of

the aerial platform and turn the battery disconnect

switch off.

2. Unlatch and swing out the control valve tray on the

right side of the machine. The brake release valve
and free-wheeling valve are located on the side of
the hydraulic manifold. The brake release pump is
on the top of the valve (refer to Figure 11.3).

Figure 11.3 – Hydraulic Tray

3. Turn and depress the brake release valve to the fully

open position.

4. Turn the free-wheeling valve counterclockwise to the

fully open position.

5. Push and release the brake release pump knob until

it can no longer be pumped.

6. Remove the wheel chocks.

7. Do not exceed 2 mph (3.2 km/h) when towing.

Warning

The aerial platform is free to move when the brakes

and free-wheeling valve are disabled. Death or serious

injury could result. Close the free-wheeling valve and

reset the brakes before operating the aerial platform.

8. Close the free-wheeling valve.

9. Drive the aerial platform forward or reverse and then

stop to reset the parking brakes. The brake release
valve can be heard when it resets, as the machine
is driven.

10. Verify that the drive system and brakes operate

properly before operating the aerial platform.

Valves with Brake Release Valve on Top of Valve

1. Chock the wheels to prevent uncontrolled motion of

the aerial platform and turn the battery disconnect

switch off.

2. Unlatch and swing out the control valve tray on the

right side of the machine. The brake release valve
and brake release pump are located on the top of the
hydraulic manifold. The free-wheeling valve is on the
side of the valve (refer to Figure 11.4).

Figure 11.4 – Hydraulic Tray

3. Turn the brake release valve clockwise to the fully

closed position. Turn the free-wheeling valve counter-
clockwise to the fully open position. Push and release
the brake release pump knob several times, until it
becomes hard to push, to release the brakes.

4. Remove the wheel chocks.

5. Do not exceed 2 mph (3.2 km/h) when towing.

Warning

The aerial platform is free to move when the brakes

and free-wheeling valve are disabled. Death or serious

injury could result. Close the free-wheeling valve and

reset the brakes before operating the aerial platform.

6. Turn the brake release valve counterclockwise to

the fully open position. Turn the free-wheeling valve
clockwise to the fully closed position.

7. Drive the aerial platform forward or reverse and then

stop to reset the parking brakes.

8. Verify that the drive system and brakes operate

properly before operating the aerial platform.

Free-Wheeling Valve

Brake Release Valve

Brake Release Pump

Free-Wheeling Valve

Brake Release Valve

Brake Release Pump

«
...
66
67
68
69
70
...
»

Содержание S3215E



























































































Отзывы:

Нет отзывов