Snorkel S3215E, Руководство оператора, Страница: 23 / 90

Chapter 3 – Safety
S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834 15
This aerial work platform is not insulated. Refer to ap-
plicable national/governmental/local regulations for safe
approach distances.
Exceeding the specified permissible maximum load
is
prohibited.
The use and operation of the aerial work platform as a
lifting tool or a crane is prohibited.
Never exceed the manual force allowed for this machine.
Distribute all platform loads evenly on the platform.
Never operate the machine without first surveying the
work area for stationary or moving obstacles and surface
hazards such as holes, drop-offs, bumps, curbs, or debris;
and avoiding them. Never strike or bump into stationary
or moving obstacles while driving or raising and lowering
the platform.
Use three points of support when entering or exiting the
platform. Grasp the handrails, not the doors, with one
hand on each side. Use two hands and one foot on the
step when climbing into and out of the platform.
Platform passengers should watch their hands and fingers
for pinch points while holding on the guardrails while the
platform is moving.
Operate machine only on surfaces capable of supporting
wheel loads.
Never operate the machine when wind speeds exceed
the machine’s wind rating.
Do not operate the aerial platform in windy or gusty
conditions. Do not add anything to the aerial platform
that will increase the wind loading such as billboards,
banners, flags, etc.
In case of an emergency, push the emergency stop button
to deactivate all powered functions.
If an alarm sounds while the platform is elevated, stop
and carefully lower platform. Move the machine to a firm,
level surface.
Climbing up the railing of the platform, standing on or
stepping from the platform onto buildings, steel or prefab
concrete structures, etc., is prohibited. Never exit or enter
the platform when it is elevated.
For AS/NZS operators, no person shall access or egress
from the platform in the elevated position (except in
an emergency) unless the requirements of AS2550.10
have been met. For full requirements refer directly to
AS2550.10
Dismantling the entry gate or other railing components
is prohibited.
Always make certain that the entry gate is
closed.
It is prohibited to keep the entry gate in an open position
when the platform is raised.
To extend the height or the range by placing of ladders,
scaffolds or similar devices on the platform is prohibited.
Never perform service on machine while the platform is
elevated without blocking the scissors structure.
Inspect the machine thoroughly for cracked welds, loose
or missing hardware, hydraulic leaks, loose wire connec-
tions, and damaged cables or hoses before using.
Verify that all placards and decals are in place and legible
before using the machine.
Never use a machine that is damaged, not functioning
properly, or has damaged or missing placards and decals.
To bypass any safety equipment is prohibited and pres-
ents a danger for the persons on the aerial work platform
and in its working range.
Never charge batteries near sparks or open flame.
Charging batteries emit explosive hydrogen gas.
Modifications to the aerial work platform are prohibited or
permissible only at the approval by Snorkel.
After use, secure the work platform from unauthorized use
by turning the keyswitch off and removing key.
Driving MEWP’s on public highways is subject to national
traffic regulations.
Certain inherent risks remain in the operation of this
machine despite utilizing proper design practices and
safeguarding.
Fall protection anchors are provided in the platform and
the manufacturer recommends the usage of a fall restraint
or fall arrest device as required by national or local reg-
ulations and standards.
Care must be taken to ensure that the machines meets
the requirements of stability during use, transportation,
assembly, dismantling when out of service, testing, or
foreseeable breakdowns.
In the event of an accident or breakdown see Chapter
11 – Emergency Operation. Do not operate the aerial plat-
form if it is damaged or not functioning properly. Qualified
maintenance personnel must correct the problem before
putting the aerial platform back into service.