manualshive.com logo in svg

Snorkel S3215E, Руководство оператора, Страница: 50 / 90

Поделиться
Скачать
Snorkel S3215E Скачать руководство пользователя страница 50

Chapter 8 – Prestart Inspection 

42

 

S3215L/S3215E/S3219E/S3220E/S3226E/S4726E/S4732E – 1500834

300700

0361259

PROPER USE OF SAFETY PROP

TO STORE SAFETY PROP

1. Remove all material from platform.
2. Raise platform until the open height is wide 

enough to position the safety prop.

3. Place safety prop in the proper position.
4. Remove hands and arms from scissors area.
5. Lower platform until scissors are supported by 

safety prop.

1. Raise platform until the open height is wide 

enough to position the safety  prop.

2. Place the safety prop in the storage position.

0361259

Death or serious injury 
might result if safety prop 
is not used and/or 
properly positioned. Use 
safety prop at all times 
when servicing machine 
with platform raised.

Proper position for safety prop use

0074311

300760

DANGER

Trays must be closed when platform is elevated.

TIPOVER  HAZARD

300760

DEATH OR SERIOUS INJURY MAY

RESULT IF MACHINE TIPS OVER

Left Side

Front

300760

0361259

300700

0074311

(Rod End of Lift Cylinder)

Содержание S3215E



























































































Отзывы:

Нет отзывов