Snap-On ControlTech Micro Скачать руководство пользователя | Manualshive

Страница: 27 / 36

background image

26



USE OF ADAPTORS, EXTENSIONS AND UNIVERSALS

Anytime an adaptor, extension or universal is used with a torque wrench in such a way that fastener
distance is different than torque wrench square drive distance at calibration, an adjustment to head
length is required to get a proper fastener torque reading.

When using wobble extension or a universal, do not exceed more than 15 degrees of offset from
perpendicular drive. Do not use a long extension with flex-drive at full flex.



CALIBRATION

Contact your Snap-on sales representative for calibration services or refer to ControlTech

TM

Micro

Calibration Manual.



CERTIFICATION

This torque wrench was calibrated at factory using torque measurement instruments that are
traceable to National Institute of Standards and Technology (N.I.S.T.). Torque parameters comply with
ISO 6789:2003 and ASME B107:300-2010 (B107.29). Note: no U.S. or International Standards exist for
angle wrenches. Angle calibration was performed on an angle gage with ±1 degree accuracy at each
45 degree indexing point throughout 180 degrees of rotation.



MAINTENANCE / SERVICE

Clean wrench by wiping with a damp cloth. DO NOT use solvents, thinners or carburetor cleaners. DO
NOT immerse in anything.
Service and repairs are to be done by Snap-on Service Centers only. Contact your Snap-on Tools
representative.
Ratchet head repair kits can be ordered from a Snap-on Representative.

NOTES: - If display shows persistent "

TORQUE ZERO ERROR

" at power on, wrench is damaged and

must be returned for repair

- If display shows

“ANGLE ERROR”

in angle mode, fastener rotation speed has exceeded

capacity of wrench.

- Wrench must be held still during angle zeroing. Motion is indicated by alternating dashes

“-

-”

on display

- Remove battery when stored for extended periods (Note: clock will revert to default

settings).

IMPORTANT!

Calibration events are recorded in wrench memory

which provides evidence to void factory certification.

«
...
25
26
27
28
29
...
»

Содержание ControlTech Micro





































Отзывы:

Нет отзывов

Похожие инструкции для ControlTech Micro

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 3

Бренд: Gallagher Страницы: 39

Бренд: Makita Страницы: 3

Бренд: Dafra Страницы: 4

Бренд: Parkside Страницы: 78

NittaBeltPoly PI-30

Бренд: Nitta Страницы: 16

Бренд: Prince Castle Страницы: 4

Бренд: Omer Страницы: 2

Бренд: Jefferson Страницы: 4

Бренд: Celltronix Страницы: 10

EdgePower EP-24V-72W

Бренд: Ubiquiti Страницы: 16

Бренд: King Canada Страницы: 5

Бренд: Hilti Страницы: 5

Бренд: Xtreme Страницы: 10

Бренд: Scell-it Страницы: 3

Бренд: Valex Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды