Snap-On ControlTech Micro Скачать руководство пользователя страница 16

Страница: 16 / 36

Press

ENTER

button to accept selection and exit to Settings menu.

Toggle Backlight Setup

This function will allow user to enable or disable backlight toggle function. If toggle mode is disabled,

BACKLIGHT

button turns on backlight and it automatically turns off after five seconds following any

last button press. If toggle mode is enabled, a

BACKLIGHT

button press will turn on backlight and it

will remain on until next

BACKLIGHT

button press.

From Settings menu, use

UP/DOWN

buttons to highlight

TOGGLE BACKLGHT

selection then press

ENTER

button.

TOGGLE BACKLGHT screen is displayed.

Use

UP/DOWN

buttons to highlight ENABLE or DISABLE (factory default) selection.

Press

ENTER

button to accept selection and exit to Settings menu.

Note: Backlight will turn off when wrench powers down either by

POWER

button press or sleep time.

Note: If toggle backlight is enabled and backlight is on, backlight will remain on during and after

applying torque.

Vibrator Configuration

This function will allow user to configure vibrator for On or Off when target is reached for preference
and/or battery power savings.

From Settings menu, use





/DOWN





buttons to highlight

VIBRATOR CONFIG

selection then

press

ENTER





button.

VIBRATOR CONFIG screen is displayed.

Use





/DOWN





buttons to toggle ON or OFF selection.

Press

ENTER





button to accept selection and exit to Settings menu.

UP/DOWN

buttons

UP/DOWN

buttons

ENTER

button

ENTER

button

EXIT

SHOW INFO

SLEEP TIME

LCD CONTRAST
KEY BEEP

AUTO BACKLIGHT

ENABLE

DISABLE

AUTO BACKLIGHT

ENABLE

DISABLE

UP/DOWN

buttons

UP/DOWN

buttons

ENTER

button

ENTER

button

EXIT

SHOW INFO

SLEEP TIME

KEY BEEP
AUTO BACKLIGHT

TOGGLE BCKLGHT

TOGGLE BCKLGHT
ENABLE

DISABLE

TOGGLE BCKLGHT

ENABLE

DISABLE

Содержание ControlTech Micro





































Результаты поиска

Содержание ControlTech Micro

Отзывы:

Похожие инструкции для ControlTech Micro

Бренды по названию

Популярные бренды

Snap-On ControlTech Micro, Инструкция пользователя

Результаты поиска

Содержание ControlTech Micro

Отзывы:

Похожие инструкции для ControlTech Micro

Бренды по названию

Популярные бренды